Base suspension alignment/setup
#1
After months of rust repair, cleaning, undercoating, etc., I am finally starting to put my ‘71 Mach 1 back together. I purchased a stock suspension rebuild kit with new control arms, shocks, shock supports, bushings, etc. I have all the components installed but am at a loss on how to setup a base alignment/setup. I had the car completely tore down to the unibody, so I won’t be able to have a final alignment done until I have the engine/transmission back in the car, but I would like to setup the front end with a base alignment to allow me to roll it around until I get everything put back in the car and can properly load the suspension and do a real alignment. 

I have measurements, etc. from the old setup that would allow me to get the tie rods and strut rods back to where they were with the old suspension, but am wondering how to set my lower control arm lengths (with the cam bolts) to get me close enough to assemble the car and roll it around some. Anyone ever done this from scratch before? Any ideas how to proceed?

Thanks in advance!
Reply
#2
Remembering My 71, the adjuster / cam bolts only had about a 1/2 inch movement total, so that isn't much as I remember. When there is no weight on the front end, and the springs are fully extended the wheels lean in at the top quite a bit. My guess would be to adjust the cam bolts to reduce the lean in at the top as much as possible. This will take some of the toe in out of things, and allow it to roll easier. if that's not enough you can adjust the tie rods and get it close to 0 toe in. Now when you add the engine, and trans you will have to undo most of what you did. To get it back near straight up and down with the weight on the suspension. The easy way to get close is take a flat piece of steel about 6 inches long, and using a magnetic angle finder, put it on the flat piece of steel and then lay it on the flat face of the wheel, and then measure the angle till you get as close to 0 degrees straight up. Then set the toe in with the tie rods and you should be in the ball park. There's a little more to it but that should get you close., and with everything being new the adjustments should be easy. Hope it helps. 

JTS
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  comp. suspension...I can't take the suspense... keith1562 3 10,989 02-18-2016, 01:37 AM
Last Post: Steven Harris
  Upgrade A '71-'73 Rearend And Suspension Mach 1 Club 0 7,403 01-10-2014, 02:21 PM
Last Post: Mach 1 Club
  72 comp. suspension keith1562 6 16,484 06-26-2012, 03:25 AM
Last Post: gxr02190
  suspension,,, keith1562 4 13,399 01-23-2012, 01:45 AM
Last Post: Steven Harris
  alignment specs GREEN72MACH1 1 6,630 12-17-2011, 03:41 AM
Last Post: BKDunha
  Suspension help roger1197 14 31,997 10-30-2011, 11:28 PM
Last Post: JTS71 Mach1
  How To Suspension Detail on 1971-1973 Mustangs Mach 1 Club 0 7,213 03-08-2011, 03:52 AM
Last Post: Mach 1 Club
  mustangs plus street heat suspension kit. sturgill 0 6,019 09-10-2010, 05:11 AM
Last Post: sturgill
  Upgrade A 1971-1973 Ford Mustang Mach 1 Rearend & Suspension Mach 1 Club 2 17,350 03-17-2010, 12:48 PM
Last Post: vamach1

Forum Jump:


Users browsing this thread: 1 Guest(s)
[-]
Latest Threads
What's One More Iron In The Fire!
Last Post: fram lee666
03-18-2024 06:21 PM
» Replies: 125
» Views: 238029
"Jacobra"
Last Post: JTS71 Mach1
06-30-2023 11:13 PM
» Replies: 86
» Views: 150590
My old Queensland Ambulance
Last Post: JTS71 Mach1
06-30-2023 11:08 PM
» Replies: 5
» Views: 1677
New member from San Jose, CA
Last Post: JTS71 Mach1
05-09-2023 08:39 AM
» Replies: 12
» Views: 3953
Saving Seatbelts
Last Post: Jim
02-19-2023 10:23 PM
» Replies: 2
» Views: 9108
Sourcing new wheels
Last Post: JTS71 Mach1
01-25-2023 02:34 PM
» Replies: 1
» Views: 1992
Shaker Air Filter
Last Post: JTS71 Mach1
01-08-2023 02:24 AM
» Replies: 3
» Views: 1464
1971 Mach 1 parting out interior parts -...
Last Post: ylwhrse
12-22-2022 01:38 PM
» Replies: 0
» Views: 640
Painting
Last Post: Rare Pony
12-14-2022 06:24 PM
» Replies: 2
» Views: 1964
WELCOME ALL NEW MEMBERS INTRODUCE YOURSE...
Last Post: JTS71 Mach1
08-31-2022 01:36 PM
» Replies: 82
» Views: 156972
1970 mach 1 matching numbers
Last Post: Kstweeter
08-31-2022 10:31 AM
» Replies: 1
» Views: 1086
Brake booster/servo hose length
Last Post: JTS71 Mach1
08-23-2022 09:40 AM
» Replies: 7
» Views: 2990
New Member
Last Post: JTS71 Mach1
08-20-2022 11:18 AM
» Replies: 2
» Views: 1497
smooth window operation on 70 Mach
Last Post: CUSTOMMISER
08-15-2022 12:10 PM
» Replies: 2
» Views: 1468
Blinkers on solid
Last Post: busted21
08-09-2022 03:58 AM
» Replies: 14
» Views: 8681
Blinkers on solid when lights on.
Last Post: JTS71 Mach1
08-08-2022 12:06 PM
» Replies: 1
» Views: 1718
351 cj running hot
Last Post: busted21
08-08-2022 12:13 AM
» Replies: 5
» Views: 3403
Major Winter projects
Last Post: JTS71 Mach1
07-09-2022 05:12 AM
» Replies: 49
» Views: 21018
Happy Fathers Day!!!
Last Post: JTS71 Mach1
06-20-2022 02:34 AM
» Replies: 0
» Views: 1681
1969 Raven Black 390 Looking For
Last Post: mason1958
06-11-2022 09:48 AM
» Replies: 10
» Views: 15074

>