Turn signals not working
#1
Purchased my 72 Mach 1 in March.  The turn signals worked but now they don't.  I have replaced the flasher and the turn signal switch.  All fuses look good.  I do not hear any clicking in the flasher unit when the turn signals are used.  All lights are working including the hazard flashers. Any thoughts?  Appreciate any assistance.
Reply
#2
Other then trying another flasher can, just to be sure you haven't gotten a bad one. It sounds like you've replaced the only other piece which is the turn signal switch it self. It isn't impossible the turn signal switch itself could actually be bad? Have you checked for power at the signal can? You should have 12 volts on one side when the signal is activated. If not follow the wires back as they come out of the turn signal switch, don't forget they also go through the brake light switch as well. The more I think about it. I believe you have a problem in the new signal switch, seeing as your 4 ways work, but the signals don't??? and they come out of the same switch. Hope it helps. 

JTS
Reply
#3
Did you replace the right flasher can? There is one for the indicators and one for the hazard lights. You might have swapped out the wrong one? I think the one for the indicators is above the glove box.
Reply
#4
That's right I forgot there are 2 cans. God I hate getting old. 

JTS
Reply
#5
(09-12-2021, 02:21 AM)JTS71 Mach1 Wrote: That's right I forgot there are 2 cans. God I hate getting old. 

JTS
Thanks for the suggestions.  I was able to get them working again by cleaning up ground wires.
Reply
#6
Yep old cars and grounds can cause lots of problems. Glad you got it sorted out. 

JTS
Reply
#7
NICE!

What a great help you all are.  :)
Reply
#8
(09-12-2021, 11:32 AM)mccuner Wrote:
(09-12-2021, 02:21 AM)JTS71 Mach1 Wrote: That's right I forgot there are 2 cans. God I hate getting old. 

JTS
Thanks for the suggestions.  I was able to get them working again by cleaning up ground wires.

I have this same problem and can't figure it out. I replace and tested everything but turn signals don't work, although hazards do. You stated you cleaned some ground wires. What ground wires did you clean and where were they located?

Thanks,
Justin
Reply
#9
The grounds are all over the place. Anywhere you see a black wire attached to a stud or body/sheetmetal directly, that's a ground. If memory servers me right the first one 1. at the battery and solenoid area, should be a 3/8 headed screw straight into the inner fender panel, and goes straight to the negative battery post. 2. There is one at the back of the engine usually a braided cable to the firewall it's self. 3. I believe there is one at the bottom of the steering column which attaches to firewall. 4. there a couple grounds at the rear tail lights along the bottom edge of the taillight panel itself. 5. there is a ground stud up behind the heater box if I remember correctly. I know there are more but those are the ones that come to mind. Hope it helps.

JTS
Reply
#10
(03-03-2022, 08:11 AM)JTS71 Mach1 Wrote: The grounds are all over the place. Anywhere you see a black wire attached to a stud or body/sheetmetal directly, that's a ground. If memory servers me right the first one 1. at the battery and solenoid area, should be a 3/8 headed screw straight into the inner fender panel, and goes straight to the negative battery post. 2. There is one at the back of the engine usually a braided cable to the firewall it's self. 3. I believe there is one at the bottom of the steering column which attaches to firewall. 4. there a couple grounds at the rear tail lights along the bottom edge of the taillight panel itself. 5. there is a ground stud up behind the heater box if I remember correctly. I know there are more but those are the ones that come to mind. Hope it helps.

JTS

Sounds good, I'll update you after I clean them!
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Where's the turn signal flasher module? Holychrome 5 22,548 11-14-2017, 07:27 PM
Last Post: Desy141
  Temp gauge not working 72mach1 4 12,870 09-10-2014, 01:08 PM
Last Post: Steven Harris
  Park Brake Warning Light - Working Bluemach 3 11,640 07-13-2013, 04:47 AM
Last Post: Rare Pony
  whats going on with my turn signl switch? mlp40 2 9,247 10-07-2012, 10:58 PM
Last Post: ohiomustang
  Turn signal switch? mlp40 5 15,096 09-22-2012, 09:24 AM
Last Post: mlp40
  Temperature gauge not working...ideas? mlp40 9 25,945 09-25-2011, 12:13 PM
Last Post: mlp40
  turn signal slows down ken72 8 21,111 09-05-2011, 12:42 AM
Last Post: rvrtrash
  Engine won't turn off! Mach Man 11 29,038 09-05-2011, 12:37 AM
Last Post: rvrtrash

Forum Jump:


Users browsing this thread: 1 Guest(s)
[-]
Latest Threads
What's One More Iron In The Fire!
Last Post: fram lee666
03-18-2024 06:21 PM
» Replies: 125
» Views: 238061
"Jacobra"
Last Post: JTS71 Mach1
06-30-2023 11:13 PM
» Replies: 86
» Views: 150866
My old Queensland Ambulance
Last Post: JTS71 Mach1
06-30-2023 11:08 PM
» Replies: 5
» Views: 1688
New member from San Jose, CA
Last Post: JTS71 Mach1
05-09-2023 08:39 AM
» Replies: 12
» Views: 3957
Saving Seatbelts
Last Post: Jim
02-19-2023 10:23 PM
» Replies: 2
» Views: 9109
Sourcing new wheels
Last Post: JTS71 Mach1
01-25-2023 02:34 PM
» Replies: 1
» Views: 1997
Shaker Air Filter
Last Post: JTS71 Mach1
01-08-2023 02:24 AM
» Replies: 3
» Views: 1466
1971 Mach 1 parting out interior parts -...
Last Post: ylwhrse
12-22-2022 01:38 PM
» Replies: 0
» Views: 640
Painting
Last Post: Rare Pony
12-14-2022 06:24 PM
» Replies: 2
» Views: 1964
WELCOME ALL NEW MEMBERS INTRODUCE YOURSE...
Last Post: JTS71 Mach1
08-31-2022 01:36 PM
» Replies: 82
» Views: 157029
1970 mach 1 matching numbers
Last Post: Kstweeter
08-31-2022 10:31 AM
» Replies: 1
» Views: 1086
Brake booster/servo hose length
Last Post: JTS71 Mach1
08-23-2022 09:40 AM
» Replies: 7
» Views: 2996
New Member
Last Post: JTS71 Mach1
08-20-2022 11:18 AM
» Replies: 2
» Views: 1498
smooth window operation on 70 Mach
Last Post: CUSTOMMISER
08-15-2022 12:10 PM
» Replies: 2
» Views: 1475
Blinkers on solid
Last Post: busted21
08-09-2022 03:58 AM
» Replies: 14
» Views: 8719
Blinkers on solid when lights on.
Last Post: JTS71 Mach1
08-08-2022 12:06 PM
» Replies: 1
» Views: 1719
351 cj running hot
Last Post: busted21
08-08-2022 12:13 AM
» Replies: 5
» Views: 3403
Major Winter projects
Last Post: JTS71 Mach1
07-09-2022 05:12 AM
» Replies: 49
» Views: 21264
Happy Fathers Day!!!
Last Post: JTS71 Mach1
06-20-2022 02:34 AM
» Replies: 0
» Views: 1685
1969 Raven Black 390 Looking For
Last Post: mason1958
06-11-2022 09:48 AM
» Replies: 10
» Views: 15080

>