ABS Control Module
#1
ABS light on and traction control light on.  Have error C1145 and C1266.  Replaced the front right wheel speed sensor, still have both codes.  I'm guessing next step is to replace the ABS control module?  Is there a good place to send the old one in to get remanufactured, or send in to get a remanufactured pard?  I don't want to just grab one on e-bay--who knows if it will be good. 

Also, any good videos around to show how to actually do it?  The one I found had a broken link. 

Thanks. Crazy
Reply
#2
Hey Stuffbert, Welcome 

It would help if you'd give us some idea of what you're working on, and we'll know if we can help you. This site is about the Mach 1 Mustangs. Which were produced in 1969 through 1973, then again in 1978, then again in 2003, and 2004. I'm just guessing you must have a 2003, or 2004 as those are the only years that could have had antilock brakes, to my knowledge. So help us out, and tell us what you've got, and we'll see what we can do. 

JTS
Reply
#3
After a quick look on the internet. It showed c1145 is for the right front wheel speed sensor. You said you replaced it. So 1 of 2 things. You didn't install it correctly, I believe that would be the older style that you had to install it into the housing, and tap it gently until it touches the back / tone wheel on the rotor. It's been a very long time since I've messed with one that old. #2 if installed correctly you can run an ohm test on the sensor, I believe it should have about 1200 to 1400 ohms. If it shows an open the wires are broke somewhere. The other test you can do is put your multi meter on the lowest dc volt scale and spin the wheel for that sensor and you should get a voltage reading to show it is close enough to the tone wheel and is reading it. If you get no reading. you may have a broken or damaged tone wheel. As for the c1266 it would appear as that is going to require a new module. I don't have a clue if there is any one who remanufactures them ????? Try Rock Auto.com as they have just about everything, and are quite reasonable. Good Luck
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)
[-]
Latest Threads
Been Awhile... '71 Rustang
Last Post: Mister 4x4
02-25-2020 07:19 AM
» Replies: 170
» Views: 188410
Floor shifter lever
Last Post: ProblemChild54
02-24-2020 06:24 AM
» Replies: 4
» Views: 87
AC/Heater control panel
Last Post: ProblemChild54
02-18-2020 01:11 PM
» Replies: 3
» Views: 244
Truth be Known
Last Post: JTS71 Mach1
02-17-2020 05:56 AM
» Replies: 4
» Views: 1063
71-73 Factory Green Floormats
Last Post: 72 Mach 1 CJ 4 speed AC PW
02-12-2020 09:48 AM
» Replies: 0
» Views: 124
Britain to ban the sale of new gas, dies...
Last Post: BLACK JADE 69
02-10-2020 11:46 PM
» Replies: 2
» Views: 161
Try This
Last Post: JTS71 Mach1
02-09-2020 01:20 PM
» Replies: 27
» Views: 19205
2021 Ford Mustang Mach 1 spy shots
Last Post: JTS71 Mach1
02-09-2020 01:10 PM
» Replies: 1
» Views: 399
69 s code trying to use hooker 6114 head...
Last Post: 1969_Mach1
02-06-2020 03:25 AM
» Replies: 7
» Views: 415
1972 Mach Original Tires , Wheels , Trim...
Last Post: Qcode
02-05-2020 11:59 AM
» Replies: 2
» Views: 224
Old new member
Last Post: Mach 1 Club
02-04-2020 02:40 PM
» Replies: 2
» Views: 357
73 Steering Wheel/Horn
Last Post: JTS71 Mach1
02-01-2020 12:25 PM
» Replies: 1
» Views: 326
68 Bullitt Mustang
Last Post: 1969_Mach1
01-27-2020 12:35 PM
» Replies: 3
» Views: 954
EFI change over from carb
Last Post: 1969_Mach1
01-27-2020 10:05 AM
» Replies: 2
» Views: 605
Truth be Known
Last Post: Mister 4x4
01-25-2020 06:46 AM
» Replies: 1
» Views: 810
Newbie - Just brought this baby home
Last Post: Mustangmike
01-20-2020 04:08 AM
» Replies: 7
» Views: 4662
Fuel line
Last Post: Mustangmike
01-20-2020 03:42 AM
» Replies: 3
» Views: 909
Newbie
Last Post: Mustangmike
01-20-2020 01:56 AM
» Replies: 6
» Views: 872
ABS Control Module
Last Post: JTS71 Mach1
01-13-2020 01:31 PM
» Replies: 2
» Views: 692
Fresh Motor
Last Post: Mustangmike
01-13-2020 04:57 AM
» Replies: 4
» Views: 1003

>