Blow by / Exhaust smoke
#11
(04-10-2014, 10:30 PM)noroz Wrote:
(04-08-2014, 10:24 AM)piper62j Wrote: In your post, you mentioned driving 500 miles since the last owner.. Is that since the engine was rebuilt? If that is the case, the rings have or were not seated properly and it will have blow by. Perform a compression test on all cylinders after making the fuel issue repairs..
Hope this helps..

This has been on my mind a bit too, though I dont recall it blowing smoke before storage, I will run a compression test as soon as ive finished with this other stuff.

Back again,
On a lighter note I found a good web site folk can check out for motor related stuff, with good prices, very specialized but worth a look www.silver-seal.com/

Well Ive done what I can so far, compression tests at 165 to 170 on all cylinders, new pcv, fuel pump, holley pain in the butt 670, reset float levels vac tested over 15 hg when tuning air/fuel this being with a
lumpy comp cam. I could keep mucking around with this, but Im seeing alot of stupid oversites from the guy who built this engine wrong length valves for the comp cams magnum valve tips causing wear on the retainers, which I am just using valve lash caps to stop further damage.
The weather is less humid now and the smoke can now be seen to be more of a light blue/ grey , which gets worse as the car gets to operating temp. Begining to look a bit more like poor ring seating or fuel wash in the bores? I might have to pull her down.SSig_help



Reply
#12
Yep I think you might be right. Sucks the first guy didn't do a good job. One thing I will tell you from my own experience with Ford motors. Ford uses a very high content of nickel in their blocks. So depending on the bore size. (if possible) It is better to cut the block to an oversize piston and rings then it is to simply hone the cylinders and get new rings to seat. The nickel makes the block so hard the new rings won't want to seat after just honing. Hairpull
The only "Other Way" I know how to seat the rings, is to drain the coolant, then run the engine till hot (15-20 minutes)and shut it off and let it sit for several hours / days then refill with coolant and see what happens. "I never said it was a good way" But it does work. Pray Good Luck JTS 71 Mach1
Reply
#13
Thanks for the heads up,
I was kinda hoping to get away with a hone, and just go for cast rings, I will give your suggestion a try, the only thing Im worried about is if the block is say at 40 thou now that this would be also risky taking it out to 60, Ive heard these blocks arent that forgiving, and the car is a full maching no vehicle. Im not that keen on the thought of liners either, cost wise that is.
Reply
#14
You are correct about the blocks being a risk at .060 the only way to know is to have it sonic checked. Some can and some can't be bored to .060 Sleeves are the only other way to preserve a numbers matching engine. Yeah it sucks. Sad JTS71 Mach1
Reply
#15
I thought you can easily go 60 on a Windsor block ?

Clevelands are the thinner castings
Reply
#16
I was never a big fan of 60 over blocks...but, yeah there are plenty of blocks out there that are. A reputable machine shop should know, if anything by experience.
Reply
#17
(04-16-2014, 08:20 AM)ohiomustang Wrote: I thought you can easily go 60 on a Windsor block ?

Clevelands are the thinner castings

You are correct Don as The Cleveland's are the thinner of the 2 and most Windsors will go .060 with out much danger but there are some that won't make .060 without being to thin thus creating a hot spot and eventual failure. I know several machinists and they definetly recommend sonic checking "any" Ford block somebody wants pushed to .060 JTS 71 Mach1
Reply
#18
If theres ever a new owner for this car he might just find his matching block in the trunkUndecided
Reply
#19
I can relate to the frustration. What's your plan now?
Reply
#20
(04-23-2014, 06:07 AM)Mustangmike Wrote: I can relate to the frustration. What's your plan now?

I decided since I need to put screw in studs on these heads, I might as well turn a negative to a positive and do that and since Im already in the neighbourhood I might look at a rebuild if needed on the bottom end.
I suspect maybe an oil control ring is at fault.

On another note can anybody tell me in regards to screw in rocker studs 3/8 on the rocker side which is the same size the original fulcrum sits on,
and using magnum roller tip rockers. Why I would need guide plates if the configuration would be identical as If I had kept the old press in studs, with the 5/16 on the rocker retaining side.
I have been trauling around on this subject can anybody shed some light on this.
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  04 Mach 1 exhaust rattle Bogie#7 11 31,158 05-30-2015, 05:47 PM
Last Post: 1969_Mach1
  Free exhaust! Mach 1 Club 2 9,868 03-12-2010, 01:19 PM
Last Post: Rare Pony

Forum Jump:


Users browsing this thread: 1 Guest(s)
[-]
Latest Threads
What's One More Iron In The Fire!
Last Post: fram lee666
03-18-2024 06:21 PM
» Replies: 125
» Views: 238054
"Jacobra"
Last Post: JTS71 Mach1
06-30-2023 11:13 PM
» Replies: 86
» Views: 150854
My old Queensland Ambulance
Last Post: JTS71 Mach1
06-30-2023 11:08 PM
» Replies: 5
» Views: 1685
New member from San Jose, CA
Last Post: JTS71 Mach1
05-09-2023 08:39 AM
» Replies: 12
» Views: 3957
Saving Seatbelts
Last Post: Jim
02-19-2023 10:23 PM
» Replies: 2
» Views: 9109
Sourcing new wheels
Last Post: JTS71 Mach1
01-25-2023 02:34 PM
» Replies: 1
» Views: 1995
Shaker Air Filter
Last Post: JTS71 Mach1
01-08-2023 02:24 AM
» Replies: 3
» Views: 1466
1971 Mach 1 parting out interior parts -...
Last Post: ylwhrse
12-22-2022 01:38 PM
» Replies: 0
» Views: 640
Painting
Last Post: Rare Pony
12-14-2022 06:24 PM
» Replies: 2
» Views: 1964
WELCOME ALL NEW MEMBERS INTRODUCE YOURSE...
Last Post: JTS71 Mach1
08-31-2022 01:36 PM
» Replies: 82
» Views: 157027
1970 mach 1 matching numbers
Last Post: Kstweeter
08-31-2022 10:31 AM
» Replies: 1
» Views: 1086
Brake booster/servo hose length
Last Post: JTS71 Mach1
08-23-2022 09:40 AM
» Replies: 7
» Views: 2995
New Member
Last Post: JTS71 Mach1
08-20-2022 11:18 AM
» Replies: 2
» Views: 1498
smooth window operation on 70 Mach
Last Post: CUSTOMMISER
08-15-2022 12:10 PM
» Replies: 2
» Views: 1472
Blinkers on solid
Last Post: busted21
08-09-2022 03:58 AM
» Replies: 14
» Views: 8715
Blinkers on solid when lights on.
Last Post: JTS71 Mach1
08-08-2022 12:06 PM
» Replies: 1
» Views: 1719
351 cj running hot
Last Post: busted21
08-08-2022 12:13 AM
» Replies: 5
» Views: 3403
Major Winter projects
Last Post: JTS71 Mach1
07-09-2022 05:12 AM
» Replies: 49
» Views: 21263
Happy Fathers Day!!!
Last Post: JTS71 Mach1
06-20-2022 02:34 AM
» Replies: 0
» Views: 1684
1969 Raven Black 390 Looking For
Last Post: mason1958
06-11-2022 09:48 AM
» Replies: 10
» Views: 15079

>