Blocked view...
#1
Early this year I had the 351cj in my 72 Mach 1, completely rebuilt. I spoke to two of the previous owners, both swore that the engine was original. So in the interest of maintaining a numbers matching car, i went so far as to have one cylinder sleeved. Weather it was a good call remains to be seen. I didn't find out until after the rebuild that the block should have a partial vin. stamped into it. I was told it was right below the head (I forget which side). I couldn't find any stamped numbers at all. Now I'm trying to check again for the number, I've looked, shot pics. of areas I couldn't see and even used modeling clay to try to retrieve a stamped number. Did all 72 Mach 1s have a partial vin stamp? If so exactly where is it? Did replacement blocks have any kind of special stampings? Did all Fords from 70-73 have the partial vin. stamp, or just the Mustangs or just the 351cj's. Sometimes I astound myself with the lack of vital knowledge I possess about these cars.
Any input(positive or constructive criticism) would be appreciated.
Thanks,
Keith

Crazy
Reply
#2
I have a VIN stamped on the drivers side under the head at the front of the engine. A bit hard to see but can be seen and it matches the car.
Reply
#3
(07-01-2013, 05:04 PM)Oztrailer Wrote: I have a VIN stamped on the drivers side under the head at the front of the engine. A bit hard to see but can be seen and it matches the car.

Thanks, I kept looking at the rear of the block. I'll check it as soon as possible,(right now I'm in the process of repainting the hood black out). At least now I Know where to look.
Thanks again,
Keith
Reply
#4
Stamped on the block LH drivers side at the back
EDIT - this info is for a 351C
It is hard to see - but you can do it with a mirror
You almost have to lay on the shock tower brace to get back there.

All 71-3 Mustangs had the last 6 of the vin stamped on engine and trans

Service blocks usually did not have stamped numbers

Don


I found your old post
I have a 72 Mach1, 351cj. Currently the engine is out and just back from the machine shop. I was expecting the block # to be "D2AE-CA, or possibly "DOAZ-D", or "DOAE-J- G". The number is in fact "DOAE-L OH4". Is this a replacement block or a standard number that I was unaware of.

Your block was cast in Aug of 1970 - it will not match a 72 car
Reply
#5
(07-02-2013, 10:13 PM)ohiomustang Wrote: Stamped on the block LH drivers side at the back
It is hard to see - but you can do it with a mirror
You almost have to lay on the shock tower brace to get back there.

All 71-3 Mustangs had the last 6 of the vin stamped on engine and trans

Service blocks usually did not have stamped numbers

Don

Any idea why mine is at the front?
Reply
#6
(07-03-2013, 01:16 PM)Oztrailer Wrote:
(07-02-2013, 10:13 PM)ohiomustang Wrote: Stamped on the block LH drivers side at the back
It is hard to see - but you can do it with a mirror
You almost have to lay on the shock tower brace to get back there.

All 71-3 Mustangs had the last 6 of the vin stamped on engine and trans

Service blocks usually did not have stamped numbers

Don

Any idea why mine is at the front?

Steve O - no clue - never saw one at the front
Could it have been done when imported ?
All the Cleveland's are at the back - What motor is in your car ?
Boss 302's were stamped on the top center of the block in the back by the intake
Reply
#7
(07-04-2013, 10:56 PM)ohiomustang Wrote:
(07-03-2013, 01:16 PM)Oztrailer Wrote:
(07-02-2013, 10:13 PM)ohiomustang Wrote: Stamped on the block LH drivers side at the back
It is hard to see - but you can do it with a mirror
You almost have to lay on the shock tower brace to get back there.

All 71-3 Mustangs had the last 6 of the vin stamped on engine and trans

Service blocks usually did not have stamped numbers

Don

Any idea why mine is at the front?

Steve O - no clue - never saw one at the front
Could it have been done when imported ?
All the Cleveland's are at the back - What motor is in your car ?
Boss 302's were stamped on the top center of the block in the back by the intake

Aussie Clevelands had the number stamped at the front of the engine on the side of the block above the fuel pump mounting apparently from some reading.

Mine is at the front of the engine in front of where the fuel pump is located on an oval/oblong flat area. I have taken a pic and circled it in yellow.

   
Reply
#8
Steve O, you number stampings are also to nice -
All the US / Cleveland stamps at the back of the block are not in line or spaced evenly or even stamped the same depth
They were done with individual number stamps
Don
Reply
#9
Thanks Don. Looks like my post won't help Keith and will be a mystery for me for a while Sad
Reply
#10
if you ever get an answer please let me know
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)
[-]
Latest Threads
What's One More Iron In The Fire!
Last Post: fram lee666
03-18-2024 06:21 PM
» Replies: 125
» Views: 238146
"Jacobra"
Last Post: JTS71 Mach1
06-30-2023 11:13 PM
» Replies: 86
» Views: 150928
My old Queensland Ambulance
Last Post: JTS71 Mach1
06-30-2023 11:08 PM
» Replies: 5
» Views: 1706
New member from San Jose, CA
Last Post: JTS71 Mach1
05-09-2023 08:39 AM
» Replies: 12
» Views: 3966
Saving Seatbelts
Last Post: Jim
02-19-2023 10:23 PM
» Replies: 2
» Views: 9114
Sourcing new wheels
Last Post: JTS71 Mach1
01-25-2023 02:34 PM
» Replies: 1
» Views: 2003
Shaker Air Filter
Last Post: JTS71 Mach1
01-08-2023 02:24 AM
» Replies: 3
» Views: 1467
1971 Mach 1 parting out interior parts -...
Last Post: ylwhrse
12-22-2022 01:38 PM
» Replies: 0
» Views: 640
Painting
Last Post: Rare Pony
12-14-2022 06:24 PM
» Replies: 2
» Views: 1971
WELCOME ALL NEW MEMBERS INTRODUCE YOURSE...
Last Post: JTS71 Mach1
08-31-2022 01:36 PM
» Replies: 82
» Views: 157079
1970 mach 1 matching numbers
Last Post: Kstweeter
08-31-2022 10:31 AM
» Replies: 1
» Views: 1087
Brake booster/servo hose length
Last Post: JTS71 Mach1
08-23-2022 09:40 AM
» Replies: 7
» Views: 3006
New Member
Last Post: JTS71 Mach1
08-20-2022 11:18 AM
» Replies: 2
» Views: 1501
smooth window operation on 70 Mach
Last Post: CUSTOMMISER
08-15-2022 12:10 PM
» Replies: 2
» Views: 1482
Blinkers on solid
Last Post: busted21
08-09-2022 03:58 AM
» Replies: 14
» Views: 8729
Blinkers on solid when lights on.
Last Post: JTS71 Mach1
08-08-2022 12:06 PM
» Replies: 1
» Views: 1720
351 cj running hot
Last Post: busted21
08-08-2022 12:13 AM
» Replies: 5
» Views: 3411
Major Winter projects
Last Post: JTS71 Mach1
07-09-2022 05:12 AM
» Replies: 49
» Views: 21300
Happy Fathers Day!!!
Last Post: JTS71 Mach1
06-20-2022 02:34 AM
» Replies: 0
» Views: 1686
1969 Raven Black 390 Looking For
Last Post: mason1958
06-11-2022 09:48 AM
» Replies: 10
» Views: 15088

>