Wholey S..T
|
Posts: 306
Threads: 111
Joined: Jul 2011
During this beautiful weather here in Illinois, I've been driving my 72 Mach 1 ,& really enjoying it! As some of you know, my daily driver is a 1969 Cougar. I apologize in advance, but my question regards my Cougar. I'm preparing to install a hood scoop (ALA Eliminator). I can't decide on the best method to cut the hood. I've got all the usual shop tools, cut-off wheel, jig saw, drill bits (up to 3/8"), torch, air compressor etc. What would you recommend as the best method while causing the least hood distortion?
Thanks for any input,
Keith
Posts: 4,181
Threads: 46
Joined: Jan 2011
I have not personally done what you are wanting to do - so please take my response in that light.
I have seen Chip Foose do it with a air cut off wheel. I personally have never had that much success with air cut off tools but I think that my biggest problem is lack of air capacity.
I believe that I would use my Bosch jig saw with a very fine tooth. First tape the hood for both protection and pattern material and then drill the corners with the appropriate drill size (to fit the blade and give the right curve diameter). I would also mark the approximate position of under hood bracing so that I knew that I was beginning to cut multiple layers.
Again, just a suggestion as I have not cut a hole in a good hood before.
Posts: 2,305
Threads: 44
Joined: May 2012
I have never cut an opening in a hood before to accommodate a scoop but if I did I would most likely use a cut-off wheel to prevent/minimize the sheet metal from warping and it provides good control over the cut. Anytime you cut, grind, or weld sheet metal it generates heat which may cause panel warping.
I would also recommend using masking tape to create a template of the area to be cut. I always use masking tape as a guide when cutting sheet metal because it keeps from deviating off course.
Maybe some else has another recommendation.
Posts: 63
Threads: 3
Joined: Aug 2011
someone several months ago was having to install rearmarker lights on their 69- 70 with new paint, you might look back and find out what they did.As I recall they had gotten it right.
I used a high speed air saw with a very fine tooth blade on mine and like the others said ..tape it... cut it slightly smaller ,better to cut too little than to mutch.
Posts: 2,305
Threads: 44
Joined: May 2012
Here is a link to a hood scoop install. It appears the tool of choice is a fine tooth jigsaw as the guys have said. Makes sense after watching the video.
http://www.youtube.com/watch?v=cxL3eobrCjs
Let us know how you make out.
Posts: 3,119
Threads: 92
Joined: Jan 2010
Nice video, it takes a lot of balls to go cutting on a good hood. I worked in a big truck shop for a lot of years and had to install all kinds of accesories. Mirrors, wind & rock deflectors, flying women, etc. after the first couple times drilling and cutting on brand new hoods it became easy. Then I decided to add the factory style GT scoop on my new 2008 Mustang, and the old jitters came back. It took 2 weeks to work up enough courage to drill all the holes in that brand new hood. All went well and it looks great. The one thing I can give as advice is measure twice! then cut once!!! If you use a cut off wheel, as Steven was talking about. (I would) Be sure to have adequate air supply as that is the key to a cut off wheel otherwise it will cut slow and stick alot. JTS 71 Mach1
Posts: 33
Threads: 22
Joined: Oct 2012
I used a fine-tooth jigsaw to cut the hole for the shaker on my 06:
+1 on all the previous advice. Measure, measure again, and lots of tape.
Posts: 306
Threads: 111
Joined: Jul 2011
(07-02-2013, 09:26 AM)OlBlooey Wrote: I used a fine-tooth jigsaw to cut the hole for the shaker on my 06:
+1 on all the previous advice. Measure, measure again, and lots of tape.
Man O man, that's a pair of truly beautiful Mustangs!! I've got some serious envying going on. Bye the way is the color of your 70 Mach 1 Grabber blue or Competition blue, or are they the same? Did you rent a helicopter to get the overhead pic? Lol
Jealously,
Keith S.
Posts: 33
Threads: 22
Joined: Oct 2012
Thanks Keith, the color is '70 code 6 Medium Blue Metallic according to the Ford reference. PPG calls it Acapulco Blue. Pic taken from a balcony over the garage.
Posts: 306
Threads: 111
Joined: Jul 2011
(11-09-2013, 07:08 AM)OlBlooey Wrote: Thanks Keith, the color is '70 code 6 Medium Blue Metallic according to the Ford reference. PPG calls it Acapulco Blue. Pic taken from a balcony over the garage.
Excellent, be careful don't lean to far over the balcony! Lol
Keith
|
Users browsing this thread: 1 Guest(s)
|
Latest Threads
|
What's One More Iron In The Fire!
Last Post: fram lee666
03-18-2024 06:21 PM
» Replies: 125
» Views: 238061
|
"Jacobra"
Last Post: JTS71 Mach1
06-30-2023 11:13 PM
» Replies: 86
» Views: 150866
|
My old Queensland Ambulance
Last Post: JTS71 Mach1
06-30-2023 11:08 PM
» Replies: 5
» Views: 1688
|
New member from San Jose, CA
Last Post: JTS71 Mach1
05-09-2023 08:39 AM
» Replies: 12
» Views: 3957
|
Saving Seatbelts
Last Post: Jim
02-19-2023 10:23 PM
» Replies: 2
» Views: 9109
|
Sourcing new wheels
Last Post: JTS71 Mach1
01-25-2023 02:34 PM
» Replies: 1
» Views: 1997
|
Shaker Air Filter
Last Post: JTS71 Mach1
01-08-2023 02:24 AM
» Replies: 3
» Views: 1466
|
1971 Mach 1 parting out interior parts -...
Last Post: ylwhrse
12-22-2022 01:38 PM
» Replies: 0
» Views: 640
|
Painting
Last Post: Rare Pony
12-14-2022 06:24 PM
» Replies: 2
» Views: 1964
|
WELCOME ALL NEW MEMBERS INTRODUCE YOURSE...
Last Post: JTS71 Mach1
08-31-2022 01:36 PM
» Replies: 82
» Views: 157029
|
1970 mach 1 matching numbers
Last Post: Kstweeter
08-31-2022 10:31 AM
» Replies: 1
» Views: 1086
|
Brake booster/servo hose length
Last Post: JTS71 Mach1
08-23-2022 09:40 AM
» Replies: 7
» Views: 2996
|
New Member
Last Post: JTS71 Mach1
08-20-2022 11:18 AM
» Replies: 2
» Views: 1498
|
smooth window operation on 70 Mach
Last Post: CUSTOMMISER
08-15-2022 12:10 PM
» Replies: 2
» Views: 1475
|
Blinkers on solid
Last Post: busted21
08-09-2022 03:58 AM
» Replies: 14
» Views: 8720
|
Blinkers on solid when lights on.
Last Post: JTS71 Mach1
08-08-2022 12:06 PM
» Replies: 1
» Views: 1719
|
351 cj running hot
Last Post: busted21
08-08-2022 12:13 AM
» Replies: 5
» Views: 3403
|
Major Winter projects
Last Post: JTS71 Mach1
07-09-2022 05:12 AM
» Replies: 49
» Views: 21264
|
Happy Fathers Day!!!
Last Post: JTS71 Mach1
06-20-2022 02:34 AM
» Replies: 0
» Views: 1685
|
1969 Raven Black 390 Looking For
Last Post: mason1958
06-11-2022 09:48 AM
» Replies: 10
» Views: 15080
|
|
|