Holley Carb Tech Needed
#1
I purchased a used Holley carb the other day from a street vendor here in my area. I bought it and the spacer for about $40.00 so I didn't think that I could go to wrong.

The list number is 9895 and the date number is 3052.

From what I can come up with it is a Model 4175, 650 CFM with vacuum secondary, a spread bore and electric choke. It is produced for replacement on small block Generic Motor V-8's.

The spacer is an Edelbrock 2696 Square bore to Quadrajet adapter.

Here then is where I need help:

# 1 - Can I use this on my 351 C - automatic application?
# 2 - Do I need to replace the linkage setup?
# 3 - Does Holley sell the linkage I need if it must be replaced?
# 4 - Dumb question - Is the bolt pattern the same?
# 5 - Pro's and Con's of running a spread bore.


Attached Files Image(s)
                   
Reply
#2
Hi Steve, Is the intake you're using either a 72 or 73? If it is, the carb should physically work as far as the throttle bore sizes without using the adaptor. You will have to measure the mounting stud spacing on the carb. and intake to make sure they're the same. You'll also have to either buy or make a gasket for mating the two. Be sure to take into account the manifold's heat riser/choke stove provision (if it has one) when choosing/making the gasket. The carb. pictured does not appear to have a ford type trans. kickdown lever. Holley does (did) make these in aftermarket kits, however they don't seem to work as well as carbs that were designed for fords at the factory (Holley). Drivability-wise, spreadbore carburetors tend to exibit what I call the bog-factor as the overly large secondaries tend to lean the engine out when they start to open if the carburetor is not set up correctly. You will probably experience a lot of trial and error with this combination. Also take into consideration the time and cost of rebuilding the carb, and possibly having to have the lower throttle plate machined as these are notorious for warping. Hope this helps - GXR
Reply
#3
Thanks GXR,

Yeah, most of the counsel I have gotten is to continue looking and i actually don't even have to do that as Don from Ohio Mustang Supply has come to my rescue once again. I will pass this carb along to someone running a Government Motors and go genuine.

I actually don't have the intake manifold yet. My motor is a 351C 2V and I am looking to use an after market intake.
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
Sad Holley rebuild kit Limeyboy 5 4,184 04-22-2021, 12:41 PM
Last Post: JTS71 Mach1
  351C Upgrade Carb norcal510 14 38,146 02-27-2014, 02:26 AM
Last Post: djjsc
  carb selection armyfox 2 10,277 04-02-2013, 03:27 AM
Last Post: JTS71 Mach1

Forum Jump:


Users browsing this thread: 1 Guest(s)
[-]
Latest Threads
What's One More Iron In The Fire!
Last Post: fram lee666
03-18-2024 06:21 PM
» Replies: 125
» Views: 238034
"Jacobra"
Last Post: JTS71 Mach1
06-30-2023 11:13 PM
» Replies: 86
» Views: 150593
My old Queensland Ambulance
Last Post: JTS71 Mach1
06-30-2023 11:08 PM
» Replies: 5
» Views: 1679
New member from San Jose, CA
Last Post: JTS71 Mach1
05-09-2023 08:39 AM
» Replies: 12
» Views: 3953
Saving Seatbelts
Last Post: Jim
02-19-2023 10:23 PM
» Replies: 2
» Views: 9108
Sourcing new wheels
Last Post: JTS71 Mach1
01-25-2023 02:34 PM
» Replies: 1
» Views: 1993
Shaker Air Filter
Last Post: JTS71 Mach1
01-08-2023 02:24 AM
» Replies: 3
» Views: 1464
1971 Mach 1 parting out interior parts -...
Last Post: ylwhrse
12-22-2022 01:38 PM
» Replies: 0
» Views: 640
Painting
Last Post: Rare Pony
12-14-2022 06:24 PM
» Replies: 2
» Views: 1964
WELCOME ALL NEW MEMBERS INTRODUCE YOURSE...
Last Post: JTS71 Mach1
08-31-2022 01:36 PM
» Replies: 82
» Views: 156986
1970 mach 1 matching numbers
Last Post: Kstweeter
08-31-2022 10:31 AM
» Replies: 1
» Views: 1086
Brake booster/servo hose length
Last Post: JTS71 Mach1
08-23-2022 09:40 AM
» Replies: 7
» Views: 2992
New Member
Last Post: JTS71 Mach1
08-20-2022 11:18 AM
» Replies: 2
» Views: 1497
smooth window operation on 70 Mach
Last Post: CUSTOMMISER
08-15-2022 12:10 PM
» Replies: 2
» Views: 1468
Blinkers on solid
Last Post: busted21
08-09-2022 03:58 AM
» Replies: 14
» Views: 8682
Blinkers on solid when lights on.
Last Post: JTS71 Mach1
08-08-2022 12:06 PM
» Replies: 1
» Views: 1719
351 cj running hot
Last Post: busted21
08-08-2022 12:13 AM
» Replies: 5
» Views: 3403
Major Winter projects
Last Post: JTS71 Mach1
07-09-2022 05:12 AM
» Replies: 49
» Views: 21111
Happy Fathers Day!!!
Last Post: JTS71 Mach1
06-20-2022 02:34 AM
» Replies: 0
» Views: 1681
1969 Raven Black 390 Looking For
Last Post: mason1958
06-11-2022 09:48 AM
» Replies: 10
» Views: 15076

>