Holley Carburetor Information
#1
The following is a partial list of Holley Carburetors and their specific information. This list covers some of the more widely used Holleys for Ford engines. 4150 carb types use a rear metering block with jets similar to the front metering blocks. 4160 carb types use a rear metering plate with passages for fuel flow instead of a metering block, thus making the overall length of the 4160 carbs shorter than 4150 carbs and requiring shorter fuel feed tubes between bowls. One reason often given for this change in design was to lower the cost of manufacture as well as eliminate the use of rear jets and metering block. The larger sized float bowls, sometimes called "Cathedral" bowls, have the float suspended from the center for better fuel levels under hard cornering. The smaller sized float bowls have the float suspended from the side. Most 600 CFM Holleys use the smaller bowls while the 725, 780, and highter CFM carbs often use the Cathedral bowls. The CFM ratings refer to the cubic feet per minute of air flow.

Without going into specific carburetor dynamics, just keep in mind that many engine variables determine what size of carburetor is best for your application. A regular Ford 302 will run just fine with a Holley 600 CFM while the Boss 302 uses a 780 Holley because of much different engine dynamics, design, and use. The stock Ford Autolite 4 barrel carburetor is rated at 470 CFM so you be the judge. Most stock 302's of the day were 2 barrel engines anyway so just going to a Ford 4 barrel carb will show significant HP increases. The rear two "barrels" of the carburetor are opened during operation in two ways, vacuum secondary and mechanical secondary. Vacuum secondary carburetors use a vacuum diagphragm to open using engine vacuum signals to let the engine "tell" the carburetor it needs more fuel under acceleration. Mechanical secondary carburetors use a mechanical linkage that opens the rear barrels as you move the throttle for more fuel. For most street use, it's recommended that you use vacuum secondary carburetors.

The power valve is a vacuum operated valve that allows fuel into the delivery circuit off idle. The rating of the power valve, such as 8.5 or 10.5, is the engine vacuum where, when it drops below that, engine vacuum is not enough to hold the power valve closed and fuel will be allowed to mix with the idle circuit. When camshafts have lower than normal engine vacuum at idle, this can cause an overly rich condition thus the reason for different power valve ratings. Stock camshafts have higher engine vacuum at idle than a racing camshaft would. Now everyone has their favorite brand of oil, gas, car, and carburetor. I myself have used and worked on Holleys since 1971. They are easy to work on and calibrate. Their worst trait is that they don't like sitting for too long. The metering block gaskets will sometimes dry out and shrink causing idle problems. Just make sure that if you have someone work on your Holley, that they know what they are doing. At any rate, here is just a basic look at some different Holley carburetors and their specifications should you decide to go this route with your engine.

Special Note: DO NOT USE the Holley rebuild kits that use the big thick nut with the needle and seat. They can strip the threads in your float bowl. Use only rebuild kits that use the Holley style needle and seat adjusting nut and screw. Just a personal warning.

   
   
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)
[-]
Latest Threads
What's One More Iron In The Fire!
Last Post: fram lee666
03-18-2024 06:21 PM
» Replies: 125
» Views: 238166
"Jacobra"
Last Post: JTS71 Mach1
06-30-2023 11:13 PM
» Replies: 86
» Views: 150942
My old Queensland Ambulance
Last Post: JTS71 Mach1
06-30-2023 11:08 PM
» Replies: 5
» Views: 1713
New member from San Jose, CA
Last Post: JTS71 Mach1
05-09-2023 08:39 AM
» Replies: 12
» Views: 3975
Saving Seatbelts
Last Post: Jim
02-19-2023 10:23 PM
» Replies: 2
» Views: 9116
Sourcing new wheels
Last Post: JTS71 Mach1
01-25-2023 02:34 PM
» Replies: 1
» Views: 2005
Shaker Air Filter
Last Post: JTS71 Mach1
01-08-2023 02:24 AM
» Replies: 3
» Views: 1469
1971 Mach 1 parting out interior parts -...
Last Post: ylwhrse
12-22-2022 01:38 PM
» Replies: 0
» Views: 642
Painting
Last Post: Rare Pony
12-14-2022 06:24 PM
» Replies: 2
» Views: 1972
WELCOME ALL NEW MEMBERS INTRODUCE YOURSE...
Last Post: JTS71 Mach1
08-31-2022 01:36 PM
» Replies: 82
» Views: 157103
1970 mach 1 matching numbers
Last Post: Kstweeter
08-31-2022 10:31 AM
» Replies: 1
» Views: 1088
Brake booster/servo hose length
Last Post: JTS71 Mach1
08-23-2022 09:40 AM
» Replies: 7
» Views: 3013
New Member
Last Post: JTS71 Mach1
08-20-2022 11:18 AM
» Replies: 2
» Views: 1503
smooth window operation on 70 Mach
Last Post: CUSTOMMISER
08-15-2022 12:10 PM
» Replies: 2
» Views: 1482
Blinkers on solid
Last Post: busted21
08-09-2022 03:58 AM
» Replies: 14
» Views: 8732
Blinkers on solid when lights on.
Last Post: JTS71 Mach1
08-08-2022 12:06 PM
» Replies: 1
» Views: 1723
351 cj running hot
Last Post: busted21
08-08-2022 12:13 AM
» Replies: 5
» Views: 3431
Major Winter projects
Last Post: JTS71 Mach1
07-09-2022 05:12 AM
» Replies: 49
» Views: 21309
Happy Fathers Day!!!
Last Post: JTS71 Mach1
06-20-2022 02:34 AM
» Replies: 0
» Views: 1686
1969 Raven Black 390 Looking For
Last Post: mason1958
06-11-2022 09:48 AM
» Replies: 10
» Views: 15093

>