The Ford V-8 Engine Workshop
#1
   
With its free breathing large port canted valve head design and rugged block, the 351 Cleveland was an engine designed to make real horsepower. The 351C was used very successfully in NASCAR and drag racing. The 400 engine has a longer stroke, and higher cylinder deck. The 351M shares this taller block with the 400.

   

The Cleveland family engines are easily identified. The water outlet sits vertically on the top of the block. The distributor leans slightly to the passenger side. The cylinder heads are large, thick in the direction between intake and exhaust flanges. The valve cover mating surface is fairly rectangular, with 8 attaching bolts. The timing chain is contained within a cavity in the block. The cover is a flat plate behind the water pump.

Cleveland Family Cylinder Heads
The Cleveland design cylinder heads are the real trick to the engine's performance. Several versions exist. Monstrous ports are found on the four barrel (4V) variety giving very high flow capacity on an all out race motor. Somewhat smaller ports on the 2V version result in increased low-end torque, perhaps better suited to today's street applications. The combustion chambers were made in closed chamber quench shape, and also in a lower compression open chamber style. Engines designed for hydraulic lifter camshafts use slotted rocker arm pedestals, for non-adjustable rockers. These slots maintain the push rod alignment. 1971 Boss and 1972 High Output engines featured mechanical lifter camshafts with flat pedestals for adjustable rocker arms and push rod guide plates. These heads also have machined valve spring seats for use with multiple coil valve springs. The high performance heads utilize single groove valve stem locks. Australian heads come in even more variety.

4-barrel heads may be identified by the casting mark at the upper corners of the valve cover mating surface. Australian heads (at least the ones I've seen) and Boss 302 heads do not have these marks. A casting number identifying the head is found on the deck side.

   

4-bolt Mains While the 4-bolt main caps are found on only some of the 351C-4V engines, all 351C blocks are cast with provisions to accept the caps. The registration saddle is machined the same wide size as the 4-bolt engines. The supporting bulkheads are the same as the 2-bolt blocks, allowing the extra holes to be drilled and tapped.
4-bolt main bearing caps are used to support higher horsepower and continued high speed operation.

These are found on:

R-code Boss 351, 1971
R-code 351 HO, 1972
Q-code 351 CJ, 1971-73

351C vs. 351M
The 351M is sort of a hybrid between a 351C and the 400. The 351C and 351M have the same bore and stroke - 4.00" x 3.50" (also shared by the 351W and the 352). The 351C, 351M, 351W, and all other small blocks share the same bore spacing and cylinder head bolt pattern. Cleveland style heads were first used on the 1969 Boss 302.

The 351M has the higher deck block of the 400. This makes the engine wider and heavier than a 351C. As a result, 351M has longer connecting rods.

The 351M uses the larger 351W / 400 sized crankshaft journals. Stronger in the heavy duty truck sense, but more friction for performance applications at high RPM.

   

* 1969/70 351W deck is 9.480"

The 351C was available with both 2-barrel and 4-barrel heads, with very different port sizes. The 4V size was the choice for high performance builders in the '70s. The 351M is available only with the smaller port, 2V heads. These are more practical on a street engine where low end torque is desired.

The 351C uses the Small Block (289/302) bellhousing bolt pattern. The 351M and 400 use the Big Block (429/460) bellhousing bolt pattern, with the exception of a fairly rare 1973 block.

All 351C blocks can be machined for 4 bolt mains.

The 351M/400 uses thinner wall block so isn't as strong after an overbore, and more prone to overheating.

351M/400 blocks cast at Michigan Casting Center before March 1977 had casting problems, resulting in cracking of the water jacket inside the lifter gallery. Blocks with date codes of 7C01 or later should be OK.

Cleveland family engines use a distributor that will physically interchange with those of the 429/460 big block.
Reply
#2
Good information :)
Reply
#3
Goodpost
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  All-Aluminum 351 Cleveland Engine Build Mach 1 Club 1 9,139 10-13-2017, 08:26 AM
Last Post: Steven Harris
  Ford 351C 4-V Marketing Manual Mach 1 Club 7 26,478 02-27-2014, 08:41 PM
Last Post: Mustangmike
  351 Cleveland Engine Mustangs, Shelby and Cobra Data Mach 1 Club 2 14,138 01-16-2014, 01:11 AM
Last Post: Steven Harris
  The Perfect Cleveland Nov 1994 Super Ford Mach 1 Club 1 10,046 01-06-2014, 04:31 PM
Last Post: gxr02190
  Drag Engines Chevy & Ford 366 Mach 1 Club 0 7,072 01-06-2014, 06:15 AM
Last Post: Mach 1 Club
  How To Balance An Engine - Engine-Balancing Basics Mach 1 Club 0 7,882 01-06-2014, 05:06 AM
Last Post: Mach 1 Club
  351 Cleveland Engine Mach 1 Club 4 20,455 07-22-2013, 01:01 PM
Last Post: JTS71 Mach1
  Which engine is this? stang98kjg 5 15,707 06-09-2012, 08:15 AM
Last Post: gxr02190
  mild engine build GREEN72MACH1 5 18,499 05-14-2012, 02:59 AM
Last Post: furray
  ford motors australian 302 cleveland @ 351 cleveland chutsonjr@yahoo.com 0 7,289 02-15-2012, 07:14 AM
Last Post: chutsonjr@yahoo.com

Forum Jump:


Users browsing this thread: 1 Guest(s)
[-]
Latest Threads
What's One More Iron In The Fire!
Last Post: fram lee666
03-18-2024 06:21 PM
» Replies: 125
» Views: 238067
"Jacobra"
Last Post: JTS71 Mach1
06-30-2023 11:13 PM
» Replies: 86
» Views: 150873
My old Queensland Ambulance
Last Post: JTS71 Mach1
06-30-2023 11:08 PM
» Replies: 5
» Views: 1688
New member from San Jose, CA
Last Post: JTS71 Mach1
05-09-2023 08:39 AM
» Replies: 12
» Views: 3957
Saving Seatbelts
Last Post: Jim
02-19-2023 10:23 PM
» Replies: 2
» Views: 9112
Sourcing new wheels
Last Post: JTS71 Mach1
01-25-2023 02:34 PM
» Replies: 1
» Views: 2002
Shaker Air Filter
Last Post: JTS71 Mach1
01-08-2023 02:24 AM
» Replies: 3
» Views: 1466
1971 Mach 1 parting out interior parts -...
Last Post: ylwhrse
12-22-2022 01:38 PM
» Replies: 0
» Views: 640
Painting
Last Post: Rare Pony
12-14-2022 06:24 PM
» Replies: 2
» Views: 1966
WELCOME ALL NEW MEMBERS INTRODUCE YOURSE...
Last Post: JTS71 Mach1
08-31-2022 01:36 PM
» Replies: 82
» Views: 157032
1970 mach 1 matching numbers
Last Post: Kstweeter
08-31-2022 10:31 AM
» Replies: 1
» Views: 1086
Brake booster/servo hose length
Last Post: JTS71 Mach1
08-23-2022 09:40 AM
» Replies: 7
» Views: 2999
New Member
Last Post: JTS71 Mach1
08-20-2022 11:18 AM
» Replies: 2
» Views: 1498
smooth window operation on 70 Mach
Last Post: CUSTOMMISER
08-15-2022 12:10 PM
» Replies: 2
» Views: 1476
Blinkers on solid
Last Post: busted21
08-09-2022 03:58 AM
» Replies: 14
» Views: 8720
Blinkers on solid when lights on.
Last Post: JTS71 Mach1
08-08-2022 12:06 PM
» Replies: 1
» Views: 1719
351 cj running hot
Last Post: busted21
08-08-2022 12:13 AM
» Replies: 5
» Views: 3404
Major Winter projects
Last Post: JTS71 Mach1
07-09-2022 05:12 AM
» Replies: 49
» Views: 21264
Happy Fathers Day!!!
Last Post: JTS71 Mach1
06-20-2022 02:34 AM
» Replies: 0
» Views: 1685
1969 Raven Black 390 Looking For
Last Post: mason1958
06-11-2022 09:48 AM
» Replies: 10
» Views: 15082

>