Front suspension coil removal DIY
#1
After searching Internet for procedure to safely remove Mustang front suspension coils with inner tool, I found many people talking about a dangerous repair, then after doing the job I decided to write this DIY.
I am not an expert mechanic, I do care a lot for safety and I try to use common sense as much as possible.
I saw videos on Internet with two experts doing this job and almost got hurt because a lack of care, “too experts” for my opinion.
Some others describe all tools that you need internal compressor, some washers and pipes to fill the gap of compressor tool, jack, jack stands and 7/8” key or socket and ratchet.
Internal compressor:

Coil compressed using pipe filler:

Before start let´s think in this, if compressor tool needs pipes to fill gap, why they don’t come with the kit?.
In that way I installed compressor tool upside down, or for me, in correct position, so:
1. Jack your beloved Mustang and install jack stand on frame.
2. Remove tire.
3. Remove shock.
4. Now install coil compressor tool, I found hard to introduce tool by motor bay opening so I unscrewed one bolt for a hook putting into hole and once is inside reassembling tool. Notice that there are longer arms than others so match them with spring lower or higher parts and tighten by hand from motor bay.



5. Place your jack below lower control arm and rise it, spring will compress with little effort, jacking force, tighten screw by hang from motor bay while rising. Once is fully raised, do some turns with key in order to have tight and reduce some length.


6. At this point all spring force is maintained in position by jack, safety issues are no problem because spring coil can’t get out of position, is maintained by upper support and saddle. You have screwed compressor tool so you can slowly lower your jack and force will be transferred from jack to compressor tool, pay attention for tool slide off, if that happens, raise jack and reposition tool. When jack is released you will have a compressed coil ready to take out of car, put it somewhere away from personnel (YES a lot of force is there), I did a saddle change and new rubber insulators.


7. Reinstall in reverse order.

Hope this helps.
Mario


Attached Files Image(s)
                                       
Reply


Messages In This Thread
Front suspension coil removal DIY - by Masol - 08-25-2015, 08:15 AM
RE: Front suspension coil removal DIY - by Masol - 08-25-2015, 08:45 AM

Possibly Related Threads…
Thread Author Replies Views Last Post
  1971 - 1973 Mach 1, what material is the "front bumper" made of? Mach 1 Club 3 16,284 05-16-2011, 06:28 AM
Last Post: Steven Harris
  Vibrations: Engine or Suspension Mach 1 Club 0 7,741 11-17-2009, 11:30 AM
Last Post: Mach 1 Club
  Install a Blueprinted Suspension on your Classic Ford Mustang by Marlon Mitchell Mach 1 Club 2 14,820 09-30-2009, 02:24 PM
Last Post: Mach 1 Club

Forum Jump:


Users browsing this thread: 1 Guest(s)
[-]
Latest Threads
What's One More Iron In The Fire!
Last Post: fram lee666
03-18-2024 06:21 PM
» Replies: 125
» Views: 238045
"Jacobra"
Last Post: JTS71 Mach1
06-30-2023 11:13 PM
» Replies: 86
» Views: 150637
My old Queensland Ambulance
Last Post: JTS71 Mach1
06-30-2023 11:08 PM
» Replies: 5
» Views: 1682
New member from San Jose, CA
Last Post: JTS71 Mach1
05-09-2023 08:39 AM
» Replies: 12
» Views: 3953
Saving Seatbelts
Last Post: Jim
02-19-2023 10:23 PM
» Replies: 2
» Views: 9109
Sourcing new wheels
Last Post: JTS71 Mach1
01-25-2023 02:34 PM
» Replies: 1
» Views: 1993
Shaker Air Filter
Last Post: JTS71 Mach1
01-08-2023 02:24 AM
» Replies: 3
» Views: 1465
1971 Mach 1 parting out interior parts -...
Last Post: ylwhrse
12-22-2022 01:38 PM
» Replies: 0
» Views: 640
Painting
Last Post: Rare Pony
12-14-2022 06:24 PM
» Replies: 2
» Views: 1964
WELCOME ALL NEW MEMBERS INTRODUCE YOURSE...
Last Post: JTS71 Mach1
08-31-2022 01:36 PM
» Replies: 82
» Views: 157015
1970 mach 1 matching numbers
Last Post: Kstweeter
08-31-2022 10:31 AM
» Replies: 1
» Views: 1086
Brake booster/servo hose length
Last Post: JTS71 Mach1
08-23-2022 09:40 AM
» Replies: 7
» Views: 2992
New Member
Last Post: JTS71 Mach1
08-20-2022 11:18 AM
» Replies: 2
» Views: 1498
smooth window operation on 70 Mach
Last Post: CUSTOMMISER
08-15-2022 12:10 PM
» Replies: 2
» Views: 1471
Blinkers on solid
Last Post: busted21
08-09-2022 03:58 AM
» Replies: 14
» Views: 8687
Blinkers on solid when lights on.
Last Post: JTS71 Mach1
08-08-2022 12:06 PM
» Replies: 1
» Views: 1719
351 cj running hot
Last Post: busted21
08-08-2022 12:13 AM
» Replies: 5
» Views: 3403
Major Winter projects
Last Post: JTS71 Mach1
07-09-2022 05:12 AM
» Replies: 49
» Views: 21129
Happy Fathers Day!!!
Last Post: JTS71 Mach1
06-20-2022 02:34 AM
» Replies: 0
» Views: 1681
1969 Raven Black 390 Looking For
Last Post: mason1958
06-11-2022 09:48 AM
» Replies: 10
» Views: 15079

>