Plastic Restoration Product
#1
Like Armor All but WAAAAYYY cheaper is Baby Oil.
I use it on plastic light lenses (improves colour and optical quality) and all plastic interior and exterior trim (improves appearance).
I have some lenses for my Daimler project that have been treated and left for some months and they have improved and returned to a very acceptable standard. Cheap, effective and pleasant to use.
Unless it is a long term 'store for restore' apply only a very light coating as for the daily drive more is not better.
I got the tip from an ex-RAAF transport bloke. They use it all the time.
Reply
#2
Yeah baby oil has a lot of automotive uses. I have used it to put a rubber mounted, slip in taillight on a semi trailer, when it was 20 degrees outside, and I couldn't get it to go in because the rubber was to stiff. Also the guys at the local dirt track spread it on their race cars before the nights racing, makes the car shine and allows the mud to wash, or fall off easier. Cool stuff baby oil. JTS 71 Mach1
Reply
#3
I never thought of the idea of using baby oil as a substitute for Armor All. I would have guessed being "oil" based it would attract more dust and dirt. Although both you and JTS both have provided some practical and economical ideas for automotive uses.
Reply
#4
That is where M1FF's statement "Less is more" Idea comes from, to much and yes it will attract dust. Be sure to use a small amount and rub in well. A good way to do it is take a typical terrycloth dishcloth, put a small amount near each corner and 1 in the middle. fold the cloth and then try to wring it out, as if it were soaked with water, turn and refold the cloth a couple different ways, being sure to wring it each time. This will spread the baby oil more evenly into the cloth. If you lay it on the dash for a couple seconds and pick the cloth up and it leaves a lot of oil you have to much oil. If after a few seconds you can see just a trace of the baby oil that is about perfect as you will have to apply pressure to spread the baby oil into the vinyl, leather, rubber, etc. This won't leave a lot for the dust to stick to and if you got to much oil, a quick wipe every couple days with a clean cloth will make it look fresh again. Hope it helps. JTS 71 mach1
Reply
#5
(03-25-2016, 03:13 AM)JTS71 Mach1 Wrote: That is where M1FF's statement "Less is more" Idea comes from, to much and yes it will attract dust. Be sure to use a small amount and rub in well. A good way to do it is take a typical terrycloth dishcloth, put a small amount near each corner and 1 in the middle. fold the cloth and then try to wring it out, as if it were soaked with water, turn and refold the cloth a couple different ways, being sure to wring it each time. This will spread the baby oil more evenly into the cloth. If you lay it on the dash for a couple seconds and pick the cloth up and it leaves a lot of oil you have to much oil. If after a few seconds you can see just a trace of the baby oil that is about perfect as you will have to apply pressure to spread the baby oil into the vinyl, leather, rubber, etc. This won't leave a lot for the dust to stick to and if you got to much oil, a quick wipe every couple days with a clean cloth will make it look fresh again. Hope it helps. JTS 71 mach1

Excellent...will give the baby oil a try this season. Thank you for the tip!
Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
  How to Clean an Protect Your Vinyl, Plastic and Rubber Surfaces Mach 1 Club 0 2,951 11-16-2009, 02:48 AM
Last Post: Mach 1 Club

Forum Jump:


Users browsing this thread: 1 Guest(s)
[-]
Latest Threads
hdshadpar
Last Post: Steven Harris
Yesterday 02:25 PM
» Replies: 3
» Views: 122
UK Mach1
Last Post: Steven Harris
Yesterday 02:16 PM
» Replies: 2
» Views: 164
1971 Boss 351
Last Post: Steven Harris
Yesterday 02:10 PM
» Replies: 4
» Views: 142
Vin Decoder
Last Post: JTS71 Mach1
02-16-2019 08:53 AM
» Replies: 8
» Views: 5327
Bonnet latches
Last Post: JTS71 Mach1
02-13-2019 02:11 PM
» Replies: 2
» Views: 165
Vin decoder
Last Post: Oztrailer
02-11-2019 07:56 PM
» Replies: 1
» Views: 208
Ignition Timing
Last Post: JTS71 Mach1
02-10-2019 09:37 AM
» Replies: 23
» Views: 3914
"Jacobra"
Last Post: JTS71 Mach1
02-10-2019 09:18 AM
» Replies: 62
» Views: 14527
New Member
Last Post: Mustangmike
02-07-2019 09:25 PM
» Replies: 8
» Views: 505
Fuse Panel on my ‘69
Last Post: 1969_Mach1
02-06-2019 06:28 PM
» Replies: 3
» Views: 276
66 Fairlane Project
Last Post: Mustangmike
02-03-2019 10:42 PM
» Replies: 542
» Views: 157311
1973 Mach 1 parts
Last Post: Steven Harris
02-03-2019 06:37 AM
» Replies: 5
» Views: 543
Newbie - Just brought this baby home
Last Post: Steven Harris
02-03-2019 06:33 AM
» Replies: 5
» Views: 593
This One's Funny!
Last Post: JTS71 Mach1
02-01-2019 10:08 AM
» Replies: 2
» Views: 374
Dash ignition light?
Last Post: JTS71 Mach1
01-21-2019 10:37 AM
» Replies: 3
» Views: 781
New addition to the stable..
Last Post: Steven Harris
01-16-2019 01:26 PM
» Replies: 5
» Views: 907
Alternator Light Won't go off
Last Post: 1969_Mach1
01-06-2019 05:35 AM
» Replies: 13
» Views: 2166
Merry Christmas 2018
Last Post: Steven Harris
12-30-2018 12:56 PM
» Replies: 10
» Views: 1197
Led lights not all that good.
Last Post: John
12-28-2018 02:12 PM
» Replies: 24
» Views: 9350
"70 Mach 1 Fuel Line Routing
Last Post: 1969_Mach1
12-28-2018 06:07 AM
» Replies: 1
» Views: 601

>