Paint Like A Pro With Spray Cans
#1
Nearly everyone in the U.S. has at least one can of spray paint in the cabinet. Spray paints are convenient and available in a virtually endless array of colors, but they have their disadvantages.

Chief among those disadvantages is, for most people, the difficulty in obtaining a uniform, deep finish. We're here to help, so before you get out the Krylon (or whatever brand you're using) sit back and read how to get excellent results.

First, you need to know a little about how spray cans are designed and how the paint inside is mixed. A spray can is technically known as an "aerosol" device. It consists of a vessel that can withstand significant internal pressure (the can); a spray nozzle that incorporates a sealing device that won't let the pressure out of the can until called for; a tube inside the can that brings the fluid (paint) to the nozzle; and the two critical elements: pressurized gas (usually carbon dioxide) and the paint.

Today's spray nozzles are really quite good. They are precision-engineered to provide a reasonably high-quality spray, with consistent droplet sizes. The spray pattern they provide isn't adjustable like air-powered spray guns are, but that isn't why so many people have a hard time getting smooth, shiny results. Those very people would encounter the same problems if they used a spray gun. The reasons good finishes are difficult are: 1) the user isn't painting properly, and 2) the paint itself is very thin (low viscosity).

Reason # 2 is impossible to fix. That is, spray paints are heavily thinned (more solvent-to-paint content) in order for them to be pushed out of the can and turned into an aerosol spray. Thicker paint would require greater gas pressure and a more sophisticated nozzle, hence leading to an air-powered paint gun. The "trick" to getting good results with thinned paint is simply to remember that it is, in fact, thinner and prone to runs. That means more thin coats.

Reason # 1 is why we are providing this article. There are many, many wrong ways to apply spray paint, all of which end in poor finishes. People hold the can too close, too far away, too long in one spot, move too fast, move to slow, etc. There are so many wrong ways to do it that we'll just concentrate on techniques to do it right. Let's paint!

But first we must make sure our work piece is ready for painting. It has been sanded, smoothed and primed, then sanded again with fine (600 grit or higher) paper. Just before painting we've wiped it again with solvent alcohol or lacquer thinner, using a paper towel. Once that dried we wiped it with a tack rag to remove dust. Now it's placed on a table or some other surface that allows it to be high enough to see clearly during spraying (we prefer to hang items from the ceiling joists with string and bent pieces of wire). Make sure there is plenty of light around the work piece.

Now we can start spraying. The proper technique will be presented by listing a series of common mistakes:

Mistake # 1- not shaking the can long enough! Now it's time to shake the paint can, and we do so until the little ball inside rattles, thinking that's long enough. Unfortunately, it usually isn't long enough. The paint pigments have most likely separated during storage, so they need quite a bit of agitation to properly mix again. The can you are using probably says to shake for some number of minutes after the ball starts rattling. Do so. In fact, shake the can for at least three minutes unless you've just used it that day. Test the spray on a piece of cardboard or paper.

   
Results when spraying too close to surface.

Mistake # 2 - not holding the can the proper distance! Spray can directions tell you how far away from the work piece to hold the nozzle. That distance is to provide the best spray pattern and most equal distribution of the paint. Test that effect on your cardboard and prove it to yourself. What the manufacturer tells you is true.

   
Spraying too far from the surface puts less of the paint on the surface and the paint can actually dry out before it reaches the surface, leaving a rough texture or dull finish to the paint.

Mistake # 3 - holding the can directly in front of your face! You can't possibly see how the paint is "wetting" the surface if the can is spraying directly in front of your eyes. If you are right-handed, hold the can at chest-height about one foot to the right of your head (the reverse if left-handed). As you spray you will be looking at your work piece at a "grazing incidence" angle and will easily see how the spray is falling onto the surface.

   
Spraying at the distance suggested on the can's label gives you cotrol over the paint and helps prevent excess paint buildup which can lead to runs.

Mistake # 4 - not moving at the right speed! Once you can see the "wetting" effect; that is, the paint falls onto the surface and just starts to become shiny, it's time to move the can along the surface. Keep it moving at all times and the correct speed is that in which the volume of paint coming out wets the surface. Moving too fast applies a "dusting" of paint that is too little for the components to "float out" to become a smooth surface. Too fast applies the paint too thick and because it is a thin fluid it will start to run and drip.

   
This is where we started. The jack stand has a smooth surface and is ready to receive the primer.
   

Mistake # 5 - not staying parallel to the work surface! You must move the can parallel to the work surface at all times. Not doing so alters the distance from the nozzle to the surface, creating Mistake # 2 again. Practice with the can before actually spraying so you know you can move easily over a large area.

   

Mistake # 6 - there's no such thing as "one coat." Good paint finishes are always built up from several layers of paint, each one applied on a "still tacky" surface. The idea is that the paint you sprayed 10 minutes ago is still uncured and soft, so the new coat will not only stick well but its solvents will tend to "re-melt" the last coat and allow the finish to create a smoother, flatter surface.

   

Mistake # 7 - Saying "that's good enough" when it's not. There will be incidences when, no matter how well you've applied the paint, it just looks lousy. Dust got in the finish, runs appeared, "orange peel" appeared, or something else affected the outcome. Big deal! When that happens, just stop and let the paint dry. Next day, sand everything smooth and put on a couple more coats. If the project really looks terrible, spread on the stripper and get the work piece back down to bare surface. Fresh paint comes off very easily and you can re-do the whole thing in short order.

   

Points To Remember

* A little practice goes a long way, so if you're not experienced at spray painting take some time to practice painting a "test" piece. Use a piece of cardboard covered with aluminum foil if you don't have a sheet of metal or plastic to practice on. Plan to waste the better part of a can of paint in the process.
* Shake the can periodically while you paint to keep the materials in proper suspension.
* Don't forget to invert the can when finished, spraying until all color disappears.
* Mount your work piece on a stand that makes it easy to rotate or otherwise change its position, so that you can get a more even finish overall.
* Keep the nozzles on your paint cans clean. If they are clogged, pull them off and soak for a few hours in lacquer thinner.
* Many paint cans only designate color on the plastic cap. Write the color on the side of the can with a marker.

Safety Stuff

Paints are generally made from toxic substances, and their solvents are equally dangerous. Ventilation and breathing protection are very important. When painting indoors you must make sure you have a good ventilating fan or blower to pull vapors outside. Wear a proper filtration mask that removes organic vapors. If you feel dizzy, nauseated or disoriented while painting, stop and get some fresh air.
Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
  70 Mach Rocker trim paint code Mach70 1 2,932 07-19-2017, 08:11 AM
Last Post: 70MachT-5
  Early Shelby - Original Paint Mach1FatherFigure 3 3,385 03-13-2016, 10:12 PM
Last Post: Mustangmike
  Great paint reference site Mach 1 Club 2 3,098 07-24-2014, 08:31 AM
Last Post: Mustangmike
  PaintScratch original factory touch up paint Mach 1 Club 1 2,646 07-23-2014, 02:53 AM
Last Post: Steven Harris
  paint rbutk 4 4,151 11-30-2013, 03:31 PM
Last Post: rbutk
  DIY How-To Auto Body Repair and Paint Training Videos Mach 1 Club 4 4,575 11-18-2012, 07:16 AM
Last Post: armyfox
  How To Adjust HVLP Paint Gun Mach 1 Club 1 2,668 11-16-2012, 04:56 AM
Last Post: Steven Harris
  Paint brands help ylwhrse 8 8,377 09-07-2011, 11:13 PM
Last Post: Rare Pony
  No paint graphics - Vinyl Striping Tape Mach 1 Club 0 2,682 09-05-2011, 07:15 AM
Last Post: Mach 1 Club
  Mustang engine color how to paint engine 1969jimmach 0 3,168 01-25-2011, 08:11 AM
Last Post: 1969jimmach

Forum Jump:


Users browsing this thread: 1 Guest(s)
[-]
Latest Threads
Tachometer Wiring
Last Post: 1969_Mach1
Today 05:03 AM
» Replies: 1
» Views: 23
66 Fairlane Project
Last Post: JTS71 Mach1
Yesterday 10:15 AM
» Replies: 524
» Views: 116645
New member 1969 Mach 1
Last Post: Mustangmike
Yesterday 09:00 AM
» Replies: 11
» Views: 955
351c wont start, help
Last Post: JTS71 Mach1
12-16-2018 08:26 AM
» Replies: 71
» Views: 4027
PCM keeps burning out have replaced for...
Last Post: Mustangbob
12-11-2018 10:58 AM
» Replies: 8
» Views: 502
70 Boss 302 - Night Mission build blog
Last Post: JTS71 Mach1
12-07-2018 01:12 PM
» Replies: 109
» Views: 69485
Alternator Light Won't go off
Last Post: 1969_Mach1
12-05-2018 11:56 AM
» Replies: 10
» Views: 640
"Jacobra"
Last Post: Steven Harris
12-04-2018 02:36 PM
» Replies: 55
» Views: 8977
My newest 1970 Mustang Fastback 302
Last Post: BLACK JADE 69
12-04-2018 12:08 AM
» Replies: 24
» Views: 2147
New guy with a question.
Last Post: 1969_Mach1
12-03-2018 06:57 AM
» Replies: 25
» Views: 1215
Dashboard lights REALLY dim, any fixes??
Last Post: Steven Harris
12-01-2018 12:04 PM
» Replies: 13
» Views: 13844
new member
Last Post: Steven Harris
12-01-2018 12:02 PM
» Replies: 4
» Views: 374
1971-73 "Clydesdales"
Last Post: Mister 4x4
11-29-2018 11:35 AM
» Replies: 26
» Views: 1391
Installing Factory gauges in a '71-'73 M...
Last Post: Mister 4x4
11-28-2018 03:26 AM
» Replies: 4
» Views: 869
Pictures and some info from a new guy
Last Post: Mister 4x4
11-28-2018 03:02 AM
» Replies: 18
» Views: 1571
Been Awhile... '71 Rustang
Last Post: Mister 4x4
11-24-2018 01:49 PM
» Replies: 143
» Views: 94021
1965 Fairlane (Mustangmike)
Last Post: JTS71 Mach1
11-23-2018 02:56 PM
» Replies: 14
» Views: 1159
Happy Thanks Giving!!!
Last Post: 1969_Mach1
11-23-2018 03:42 AM
» Replies: 2
» Views: 380
How not to Handle A DUI Checkpoint?!?!
Last Post: Vanbens91
11-14-2018 07:22 PM
» Replies: 1
» Views: 2188
Led lights not all that good.
Last Post: Mustangmike
11-14-2018 09:44 AM
» Replies: 20
» Views: 6092

>