Rear Axle Gears
#1
I recently purchased a set of 3.70:1 ring and pinion gears for the 9" rear axle in my 69 Mach 1.  I chose U.S. Gear because they are made here and have mostly good reviews.  Anyway, they come with a few teeth with gear marking compound on them showing the contact pattern from lapping at the mfg.  The drive side looks nice, centered on the tooth, the coast side is not very good at all, it is near the toe (inside edge) of the tooth.  I haven't built many rear axles, but I encountered this once in the past and I returned the gears for another set and all was fine.  My question is, are these gears going to make noise when coasting because the coast side contact pattern is not very good?  I'd rather exchange them now before trying to install them.

Thanks
Reply
#2
Man Mike, boy you are working the old brain to hard. I think you'll be ok, with the coast side being being closer to the center. It seems to me they whine when the coast side, is out at the outer edge. The pull side is the most critical as you know. I'm trying to remember for sure. but I think it should be ok. When you get the pattern out toward the outer portion of the ring gear is where you get your whine. I'd be dang sure to check the play, and back lash once installed. I know they come with a crush sleeve now a days. but that wasn't the case back in 69". So I'd probably check and set every thing just like we did years ago, with shims if necessary. Good Luck.

JTS
Reply
#3
I'm getting older, but vaguely recall from a class on differentials back in the 1980's that a pattern close to the inside of the ring gear is stronger but has a tendency to cause noise.  And when you coast the ring gear tries to pull the pinion gear closer to it and walk the pattern to the inside.  I haven't done enough of these to go by experience.  So when things don't look textbook perfect I don't know what to do.  I got them from Summit Racing, I think I'll have them exchanged.  If the next set is the same, I'll use them.

I've researched reviews on different brands of ring and pinion gears and the consensus is basically avoid the value lines regardless of brand.  For every bad experience of a brand, there is always a good experience.  But, from people that do this for a living, they always seem to say, use OEM if possible, for aftermarket it's a gamble whether or not you get a good set.  From what I understand, there are only a few ring and pinion gear mfgs in the world, U.S. gear being about the only U.S. mfg.  All brands buy from these mfgs. then inspect them and determine which sets go into their value line boxes and which set goes into their upper end boxes.

I know MustangMike has had good luck with Yukon gears.  But, those are usually at least $100 more than other brands.  Plus, Yukon buys from the same mfgs. as the others.  Motive's performance line of gears, made in Italy, I've had good luck with.  Just thought I'd try a U.S. made gear this time around.
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  My rear tires are rubbing! Jonner B 17 7,105 10-05-2019, 11:21 AM
Last Post: JTS71 Mach1
  69 Mach 1 rear seat install RostaRob 8 7,244 06-29-2019, 02:44 AM
Last Post: rindel
  Just had rear window gasket installed on 69 mustang rindel 9 17,325 11-01-2015, 03:50 PM
Last Post: 1969_Mach1
  73 rear window seal jjorge 7 12,206 06-20-2014, 10:46 PM
Last Post: ohiomustang
  Rear Bumper Accents martyfras 0 4,196 02-23-2014, 09:11 AM
Last Post: martyfras
  9 inch rear axles & gears ylwhrse 2 7,170 06-26-2013, 04:00 PM
Last Post: ylwhrse
  1973 Fuel tank and rear springs SWOMACH1 16 21,024 05-22-2012, 12:12 PM
Last Post: turtle5353
  rear view mirror button finley 5 10,243 04-04-2012, 05:47 AM
Last Post: Steven Harris
  Rear Torque Boxes Vacca11 5 10,875 11-13-2011, 10:14 AM
Last Post: BKDunha
  Rumble from Rear of Mach Rare Pony 5 9,125 10-23-2011, 01:14 AM
Last Post: Steven Harris

Forum Jump:


Users browsing this thread: 1 Guest(s)
[-]
Latest Threads
Here are some pics of my cars
Last Post: lashary1
Yesterday 03:49 PM
» Replies: 10
» Views: 13906
grille and lower grille color
Last Post: wvayn
08-03-2020 10:05 PM
» Replies: 5
» Views: 406
Squirrels!
Last Post: Oztrailer
08-01-2020 06:11 PM
» Replies: 1
» Views: 759
Windshield Washer Setup
Last Post: RobbyMach1
07-28-2020 02:43 AM
» Replies: 7
» Views: 12941
1969 Lilac
Last Post: bob.harlan
07-28-2020 01:35 AM
» Replies: 2
» Views: 570
Mystery connector on A Pillar
Last Post: mikemcg
07-26-2020 06:46 AM
» Replies: 13
» Views: 1864
69 Mach I body shell
Last Post: JTS71 Mach1
07-25-2020 06:18 AM
» Replies: 7
» Views: 1036
Fuel pump & carb replacement
Last Post: Tom W
07-23-2020 07:39 AM
» Replies: 28
» Views: 2531
Rear Axle Gears
Last Post: 1969_Mach1
07-21-2020 02:23 AM
» Replies: 2
» Views: 802
69 Coupe
Last Post: ssjohns
07-20-2020 01:37 AM
» Replies: 0
» Views: 674
1969 Mach1 Parking light socket with wir...
Last Post: rindel
07-15-2020 12:58 PM
» Replies: 2
» Views: 962
Pulling the motor
Last Post: JTS71 Mach1
07-13-2020 11:28 AM
» Replies: 9
» Views: 1657
New Member
Last Post: Smileys35
07-12-2020 02:15 PM
» Replies: 6
» Views: 1320
Just joined
Last Post: Smileys35
07-12-2020 04:42 AM
» Replies: 5
» Views: 1294
Been Awhile... '71 Rustang
Last Post: Mister 4x4
07-09-2020 10:42 AM
» Replies: 176
» Views: 213666
The 2021 Ford Mustang Mach 1 Is Back Wit...
Last Post: JTS71 Mach1
07-07-2020 09:31 AM
» Replies: 5
» Views: 1454
Ford unveils 2021 Mustang Mach 1
Last Post: Mister 4x4
07-06-2020 06:17 AM
» Replies: 2
» Views: 1486
Happy Father's Day
Last Post: JTS71 Mach1
06-22-2020 01:24 AM
» Replies: 0
» Views: 994
2021 Ford Mustang Mach 1 builds a bridge...
Last Post: Mach 1 Club
06-17-2020 01:20 AM
» Replies: 0
» Views: 1308
Daddy's Home!
Last Post: JTS71 Mach1
06-09-2020 12:05 PM
» Replies: 0
» Views: 5079

>