Oil pressure range when stopping
#1
Hi Guys,

My oil pressure dummy light started flickering when coming to a stop then it started getting worse. I tested the pressure with a mechanical oil pressure gauge and was getting about 60 psi after a cold start. I recently replaced the oil sensor and switched over to an electric oil sender and gauge. I get about 60 psi after a cold start and while driving when warm. The driving range is about 40-60 psi when hot but when I come to a full stop, the needle drops to 10 psi. I suspect my idle may be too low because it feels like the car is border line choking. At what psi should i see when coming to a full stop?

BTW - when I put it in neutral, it jumps to 20 psi.
Reply
#2
this is a 69 mach 1 351w with mild cam and auto.
Reply
#3
Is this a fresh, or high mileage engine? If it's a old high mileage engine, Fords were pretty know for low oil pressure at idle. Which with an automatic was supposed to be set around 700 RPM You can easily raise the idle to 800 or 900 and probably see an improvement as noticed by putting the car in neutral. The problem is normal engine wear/exaggerated engine wear. No telling how it was taken care of before you got it, oil changes etc. If the raised idle works (roughly 20 psi in Drive) and keeps the light off. I'd drive it as a little extra clearance in the bearings won't really hurt it as long as you don't "lose oil pressure". Change to a higher viscosity oil, instead of 10w30 or 10w40 go up to 20w50. I would also put a quart of Lucas, in place of 1 quart of oil when changing the oil. The other choice is to rebuild the bottom end, new crank, bearings and an oil pump, will most likely bring the oil pressure back to where it should be. If you're going to all that trouble you might as well rebuild the whole engine. As I said I'd put the heavier oil and Lucas in it and drive it. I gone 10's of thousands of miles in several old Fords with low oil pressure at Idle, and never blew the bottom end no matter how hard I ran it. Just some personal insight and experience. Hope it helps. JTS 71 Mach1
Reply
#4
From earlier threads on this site I think this motor was recently rebuilt. How thoroughly, I don't know. But I recall threads during a rebuild.

At idle, with only 10 psi, if bearings are the cause, I would think some mechanical noises would be heard. Not necessarily knocking noises, but maybe sounding like marbles are rolling around in the crankcase.

Is it possible for some reason the pressure relief valve in the oil pump is stuck open? From my experience on stock and high volume oil pumps (not high pressure) the pressure relief valve starts to open in a range of 55 to 60 psi range. So at cruise his oil pressure is normally high enough to open the pressure relief valve. But, maybe it is stuck open? If so, that could be an inexpensive one day repair.
Reply
#5
Your idle pressure is 'within limits'. If the relief valve was open you would get just about nil at idle.
Bring the idle up to 'book' and fit a new light sender. Your engine seems fine. Just to be sure, even though it might be new, change the oil filter and buy a good brand. I have been caught with a clogged filter - long story - changing the filter was all that was needed - oil and filter were 'fresh'.
Reply
#6
Thank you very much helped, for a long time I was looking for the answer to this question.
192.168.o.1 - 192.168.0.1 router login
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  72 Mach 1 Power Steering Pressure Hose Jelly 1 2,941 11-07-2021, 08:42 AM
Last Post: JTS71 Mach1
  Brakes not holding pressure?!?! armyfox 6 16,552 06-09-2013, 10:46 AM
Last Post: 68machowner

Forum Jump:


Users browsing this thread: 5 Guest(s)
[-]
Latest Threads
What's One More Iron In The Fire!
Last Post: fram lee666
03-18-2024 06:21 PM
» Replies: 125
» Views: 238035
"Jacobra"
Last Post: JTS71 Mach1
06-30-2023 11:13 PM
» Replies: 86
» Views: 150593
My old Queensland Ambulance
Last Post: JTS71 Mach1
06-30-2023 11:08 PM
» Replies: 5
» Views: 1679
New member from San Jose, CA
Last Post: JTS71 Mach1
05-09-2023 08:39 AM
» Replies: 12
» Views: 3953
Saving Seatbelts
Last Post: Jim
02-19-2023 10:23 PM
» Replies: 2
» Views: 9108
Sourcing new wheels
Last Post: JTS71 Mach1
01-25-2023 02:34 PM
» Replies: 1
» Views: 1993
Shaker Air Filter
Last Post: JTS71 Mach1
01-08-2023 02:24 AM
» Replies: 3
» Views: 1465
1971 Mach 1 parting out interior parts -...
Last Post: ylwhrse
12-22-2022 01:38 PM
» Replies: 0
» Views: 640
Painting
Last Post: Rare Pony
12-14-2022 06:24 PM
» Replies: 2
» Views: 1964
WELCOME ALL NEW MEMBERS INTRODUCE YOURSE...
Last Post: JTS71 Mach1
08-31-2022 01:36 PM
» Replies: 82
» Views: 156994
1970 mach 1 matching numbers
Last Post: Kstweeter
08-31-2022 10:31 AM
» Replies: 1
» Views: 1086
Brake booster/servo hose length
Last Post: JTS71 Mach1
08-23-2022 09:40 AM
» Replies: 7
» Views: 2992
New Member
Last Post: JTS71 Mach1
08-20-2022 11:18 AM
» Replies: 2
» Views: 1497
smooth window operation on 70 Mach
Last Post: CUSTOMMISER
08-15-2022 12:10 PM
» Replies: 2
» Views: 1469
Blinkers on solid
Last Post: busted21
08-09-2022 03:58 AM
» Replies: 14
» Views: 8682
Blinkers on solid when lights on.
Last Post: JTS71 Mach1
08-08-2022 12:06 PM
» Replies: 1
» Views: 1719
351 cj running hot
Last Post: busted21
08-08-2022 12:13 AM
» Replies: 5
» Views: 3403
Major Winter projects
Last Post: JTS71 Mach1
07-09-2022 05:12 AM
» Replies: 49
» Views: 21114
Happy Fathers Day!!!
Last Post: JTS71 Mach1
06-20-2022 02:34 AM
» Replies: 0
» Views: 1681
1969 Raven Black 390 Looking For
Last Post: mason1958
06-11-2022 09:48 AM
» Replies: 10
» Views: 15078

>