Home Sell Your Mustang/Parts Arizona Mustangs Games Contact Us


70 Tilt Column
Author Message
Stangman69SCJ Offline
Junior Member
*****

Posts: 16
Threads: 11
Joined: Jul 2014
#1
70 Tilt Column
Does anyone know on a 70 tilt, is there a spring that goes on the shaft tip prior to attaching the steering wheel? I've worked on 69 tilts and there is a small tight spring. Standard wheels get a wider, spring that is offered in most catalogs. Most tilt columns i've googled and looked at do not show anything?? Any help would be appreciated. Basically having trouble getting the horns to work. Have newly restored rimblo wheel. Have checked horns, which work. Have omed the rim blo switch which works..?????
09-18-2016, 11:54 PM
Find Reply
JTS71 Mach1 Offline
Super Moderator
*********

Posts: 2,213
Threads: 45
Joined: Jan 2010
#2
RE: 70 Tilt Column
Wow I was sure there was a thread on that subject somewhere on the site. I was not able to find one??? It's been years since I've had one apart so the memory is pretty fuzzy, but as I remember they did have a stout spring in them which kept everything snugged up as you tilted the wheel up and down. I found a picture of it in my Haynes manual. The heavy spring is located in the lower housing and pushes up on the upper housing. The hinge pins connect the 2 housings together so the spring is on the bottom side of the column and pushes up on the upper housing. I believe the older column had a stout spring that went over the shaft itself similar to a 70's GM column I think???? I hope somebody can help you a little more. Cause I can't make the Flippin Kodak printer, scan the picture out of the manual for you. Sorry about that. DAMN COMPUTERS! JTS 71 Mach1
"We built these cars to drive the "HELL" out of them, not to be museum pieces!" Carroll Shelby

2008 Mustang V6 5 speed "Diablo Sport Predator" tuner, 87 octane tune. WOW!
1994 Ford F150 Shortbed
1986 Honda 450 Rebel
1995 Honda Pacific Coast
1989 Jacobra / Jag xjs
09-19-2016, 01:38 PM
Find Reply
j-cobb9 Away
Member
*****

Posts: 83
Threads: 3
Joined: Jan 2015
#3
RE: 70 Tilt Column
Don't hate me if I am wrong, its been a very long time for me also, if you haven't figured it out yet, here it goes.
Typically there is a spring and a clip that holds up the shaft.
The horn runs though the turn signal switch through the two little brass spring loaded contacts. Check the springs on them both of them, should be the same height. If not the spring is weak or broken. also look on the under side of the steering wheel. The brass contact on that may be broken or cracked.( very common). With the steering wheel off you can also jump the two brass contacts together the horn should blow, witch means your horns and the wiring to the horns are good.
If you have a ford dealer in your area that looks like time forgot, and you go in when its not so busy, they may have the old books or micro fish that you can look at, will have the blown up view of the steering column. Hope this helps
cheers J
09-25-2016, 11:23 PM
Find Reply
Steven Harris Offline
Super Moderator
*********

Posts: 4,028
Threads: 49
Joined: Jan 2011
#4
RE: 70 Tilt Column
No help from me but here's hoping you have got it all figured out.
[Image: Arizona_flag_32w.gif]
Southern Arizona
Current Mustangs:
1973 Mach 1

1971 Mustang Grande
1986 5.0 GT Convertible

[Image: stevenharris.jpg]
You are not allowed to view links. Register or Login to view./
10-02-2016, 05:37 AM
Website Find Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
  Lower steering column cover clips jrocket 0 1,096 03-17-2013, 06:32 AM
Last Post: jrocket

Forum Jump:


Welcome, Guest
You have to register before you can post on our site.


  

Password
  





Online Users
There are currently 107 online users.
» 1 Member(s) | 106 Guest(s)
Mach 1 Club

Forum Statistics
» Members: 1,262
» Latest member: jason
» Forum threads: 5,865
» Forum posts: 33,863

Full Statistics

Search Forums

(Advanced Search)