How To Balance An Engine - Engine-Balancing Basics
#1
   
A Question of Balance
Before digging into the custom stuff, we figured we'd better brush up on exactly how OE engines are balanced and look into the internal/external-balance issue. To start us on our journey, we decided to talk to Scat Crankshaft's Tom Lieb, who has a strong background in the area of balancing. Lieb is very opinionated about this issue because he has seen just about every imaginable variation on crankshaft failure. Most of these are not due to poor quality, as many think. Usually, the engine has either been abused with excessive rpm, balanced improperly, or often suffered some parts-abusing combination of the two.

Let's start with a short lesson on crankshaft design. Crankshaft counterweights are designed to offset (or balance, if you will) the inertia effect of a relatively heavy piston and connecting rod moving in both a rotational and reciprocating (up-and-down) fashion at speed. The weight of the piston-and-rod combination affects the size and placement of the counterweight. A longer stroke combined with a heavy piston, pin, and ring package requires a larger counterweight (more mass) to balance the greater reciprocating weight. Most V-8 engines use large counterweights toward the front and rear of the crankshaft, leaving the center portion without counterweights. That splits the engine into front and rear halves. The positions of the counterweights on all V-8 90-degree crankshafts are the same. The height of the counterweight as measured outward from the crankshaft centerline is limited by both the cylinder block and by the placement of the bottom of the cylinders. A counterweight placed farther away from the crank centerline has more balance effect, but it is limited by the width of the block crankcase. Weights placed toward both ends of the crank also have a greater effect and therefore don't need to be as large to effectively balance the engine. This makes the overall crank lighter.

Internal vs. External Balance
Packaging is also an important issue. During the design of the 400ci small-block, a major engineering hurdle was insufficient real estate inside the small-block crankcase for the larger counterweights demanded by the 400's supersized 4.125-inch piston. This was especially difficult in the rear of the engine because the rear crankcase area on a small-block Chevy is restricted by the placement of the oil filter. The solution called for external balance weights placed on the harmonic balancer and flywheel/flexplate. One advantage to external weights is that they are generally lighter because they are positioned at the extreme ends of the crankshaft. The disadvantage is that these offset weights impart their own twisting forces back into the crankshaft, which is not good. This same situation occurs with the 454ci big-block Chevy, which is also the only production big-block that uses external weights to balance the engine.

Complete article with photos:
http://www.carcraft.com/howto/ccrp_0803_...ewall.html
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  All-Aluminum 351 Cleveland Engine Build Mach 1 Club 1 9,144 10-13-2017, 08:26 AM
Last Post: Steven Harris
  351 Cleveland Engine Mustangs, Shelby and Cobra Data Mach 1 Club 2 14,141 01-16-2014, 01:11 AM
Last Post: Steven Harris
  351 Cleveland Engine Mach 1 Club 4 20,458 07-22-2013, 01:01 PM
Last Post: JTS71 Mach1
  Which engine is this? stang98kjg 5 15,714 06-09-2012, 08:15 AM
Last Post: gxr02190
  mild engine build GREEN72MACH1 5 18,505 05-14-2012, 02:59 AM
Last Post: furray
  Some basics of Cleveland building (in no particular order) Mach 1 Club 3 15,996 03-20-2012, 11:47 AM
Last Post: turtle5353
  balancing act keepemsharp 7 21,626 12-15-2011, 07:01 AM
Last Post: keepemsharp
  429 P.I Engine Grabber Lime 5 18,247 09-07-2011, 08:37 AM
Last Post: Grabber Lime
  Building the Cobra Jet Engine Mach 1 Club 3 12,825 08-28-2011, 02:45 AM
Last Post: Mach 1 Club
  "Clevor" Engine Build? Klutch 2 13,570 08-10-2011, 11:39 AM
Last Post: 70427w

Forum Jump:


Users browsing this thread: 1 Guest(s)
[-]
Latest Threads
What's One More Iron In The Fire!
Last Post: fram lee666
03-18-2024 06:21 PM
» Replies: 125
» Views: 238164
"Jacobra"
Last Post: JTS71 Mach1
06-30-2023 11:13 PM
» Replies: 86
» Views: 150940
My old Queensland Ambulance
Last Post: JTS71 Mach1
06-30-2023 11:08 PM
» Replies: 5
» Views: 1713
New member from San Jose, CA
Last Post: JTS71 Mach1
05-09-2023 08:39 AM
» Replies: 12
» Views: 3974
Saving Seatbelts
Last Post: Jim
02-19-2023 10:23 PM
» Replies: 2
» Views: 9116
Sourcing new wheels
Last Post: JTS71 Mach1
01-25-2023 02:34 PM
» Replies: 1
» Views: 2004
Shaker Air Filter
Last Post: JTS71 Mach1
01-08-2023 02:24 AM
» Replies: 3
» Views: 1469
1971 Mach 1 parting out interior parts -...
Last Post: ylwhrse
12-22-2022 01:38 PM
» Replies: 0
» Views: 642
Painting
Last Post: Rare Pony
12-14-2022 06:24 PM
» Replies: 2
» Views: 1972
WELCOME ALL NEW MEMBERS INTRODUCE YOURSE...
Last Post: JTS71 Mach1
08-31-2022 01:36 PM
» Replies: 82
» Views: 157098
1970 mach 1 matching numbers
Last Post: Kstweeter
08-31-2022 10:31 AM
» Replies: 1
» Views: 1088
Brake booster/servo hose length
Last Post: JTS71 Mach1
08-23-2022 09:40 AM
» Replies: 7
» Views: 3011
New Member
Last Post: JTS71 Mach1
08-20-2022 11:18 AM
» Replies: 2
» Views: 1503
smooth window operation on 70 Mach
Last Post: CUSTOMMISER
08-15-2022 12:10 PM
» Replies: 2
» Views: 1482
Blinkers on solid
Last Post: busted21
08-09-2022 03:58 AM
» Replies: 14
» Views: 8732
Blinkers on solid when lights on.
Last Post: JTS71 Mach1
08-08-2022 12:06 PM
» Replies: 1
» Views: 1723
351 cj running hot
Last Post: busted21
08-08-2022 12:13 AM
» Replies: 5
» Views: 3418
Major Winter projects
Last Post: JTS71 Mach1
07-09-2022 05:12 AM
» Replies: 49
» Views: 21309
Happy Fathers Day!!!
Last Post: JTS71 Mach1
06-20-2022 02:34 AM
» Replies: 0
» Views: 1686
1969 Raven Black 390 Looking For
Last Post: mason1958
06-11-2022 09:48 AM
» Replies: 10
» Views: 15093

>