Mustang Wheel Spacer Tech
#1
Are wheel spacers safe?

Yes. When properly installed they are just as safe as wheels installed without spacers.

Will wheel spacers cause my wheel studs to bend?

No. The load from a wheel is transferred to the axle/hub through the friction of the clamped joint, not through the wheel stud. A wheel stud can only bend if the lug nuts are not properly torqued, in which case the wheel is about to fall off, anyway.

The Physics of Keeping the Wheels On


As long as the wheel, hub, and spacer are stiff enough to prevent flexing and loss of clamp force, the cause of most wheel stud failures is under tightened lug nuts (not enough clamping force) or over tightened lug nuts (the stud has been stretched past it's elastic limit, so the clamping force goes away). Therefore, properly installed wheel spacers are perfectly safe.
The wheel stud applies a clamping force that holds the wheel to the hub. When the lug nuts are tightened, the wheel studs stretch elastically, like very stiff springs. The lug nuts should be tightened until the stud is at 90% of its elastic limit. This will provide the greatest possible force to hold the wheel to the hub.
The amount of clamping force at a joint is important because of the coefficient of friction (Cf). The more clamping force applied to the joint (in this case the joint between the wheel and the hub), the more force required to make the wheel slip relative to the hub. Unless the wheel slips on the hub, there cannot be any bending load on the stud.
Coefficient of friction -- There is friction between the wheel face and hub face. This friction can be measured, and it is called the "coefficient of friction". The coefficient of friction (Cf) is the ratio of normal force, at the intersection of two surfaces, to the lateral force required to slip the bodies relative to one another. As an example, good street tires have a Cf of 0.9. This means that if there is a 100-pound vertical force applied to the tire, the tire can generate 90 lbs. of cornering force before it slides.
When the car starts moving, the stress applied to the stud does not change appreciably, unless one of two things happens:
The vertical component of any external force applied to the wheel is so great that the clamping force is not sufficient to hold the wheel in place, and it slips on the hub. At this point the stud is loaded in bending and in shear, and may yield, or even break.
Some portion of the clamped joint, wheel, or hub is not stiff enough to prevent flexing, and allows the tension load on the stud to drop to zero. With no tension load on the stud, the clamped joint is no longer tight. The wheel can then move relative to the hub, and place a bending load on the studs.
Inserting a wheel spacer between the hub and wheel changes nothing about these physics.
The hub center of a hubcentric spacer does not hold the spacer on the hub or reduce the chance of stud failure. There is never any load on the lip of the wheel spacer. For there to be a load on the lip, the friction force in the joint must have been completely overcome. The lip on a hubcentric wheel spacer serves only as an aid for wheel installation.
Increasing the length of the wheel studs to use a wider wheel spacer has no appreciable effect.
Reply
#2
Damn good and correct explanation. You da Man! Where do you come up with this stuff? Bow JTS 71 Mach1
Reply
#3
I'm obsessed. Notallthere
Reply
#4
Goodpost

I've never needed spacers, but have always wondered about the impact of using them.
Reply
#5
Obsessed or devoted I pick the later of the 2. GoodpostGoodpost
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  50 Best Vintage Mustang Bolt-Ons Mach 1 Club 1 10,779 10-30-2018, 03:35 PM
Last Post: Steven Harris
  28 Classic Mustang Restoration Tips You Have To See Mach 1 Club 0 6,416 10-13-2018, 03:44 PM
Last Post: Mach 1 Club
  How To Tech Qa Mach 1 Club 1 7,215 11-06-2017, 06:47 AM
Last Post: 1969_Mach1
  TECH - Basic battery and electrical checks Mach 1 Club 1 8,845 09-27-2014, 10:10 AM
Last Post: Mach1FatherFigure
  50 tech tips for your classic Mustang! Mach 1 Club 2 11,844 02-11-2012, 07:07 AM
Last Post: Mach 1 Club
  25 weekend projects for your classic Mustang Mach 1 Club 3 13,834 02-11-2012, 01:43 AM
Last Post: Masterblaster7212
  VIDEO - How to install a pitman arm nut: 1972 Ford Mustang Fastback Mach 1 Club 0 9,409 01-01-2012, 09:04 AM
Last Post: Mach 1 Club
  Mustang Club Of America's Tips To The Winner's Circle - How To Win! Mach 1 Club 1 14,648 01-01-2012, 06:44 AM
Last Post: Steven Harris
  How to own a classic Mustang and drive it to Mach 1 Club 0 7,847 12-14-2011, 01:49 AM
Last Post: Mach 1 Club
  1970 mustang wiring diagram 1969jimmach 4 18,558 06-21-2011, 12:56 AM
Last Post: Gos1

Forum Jump:


Users browsing this thread: 1 Guest(s)
[-]
Latest Threads
What's One More Iron In The Fire!
Last Post: fram lee666
03-18-2024 06:21 PM
» Replies: 125
» Views: 238055
"Jacobra"
Last Post: JTS71 Mach1
06-30-2023 11:13 PM
» Replies: 86
» Views: 150857
My old Queensland Ambulance
Last Post: JTS71 Mach1
06-30-2023 11:08 PM
» Replies: 5
» Views: 1686
New member from San Jose, CA
Last Post: JTS71 Mach1
05-09-2023 08:39 AM
» Replies: 12
» Views: 3957
Saving Seatbelts
Last Post: Jim
02-19-2023 10:23 PM
» Replies: 2
» Views: 9109
Sourcing new wheels
Last Post: JTS71 Mach1
01-25-2023 02:34 PM
» Replies: 1
» Views: 1995
Shaker Air Filter
Last Post: JTS71 Mach1
01-08-2023 02:24 AM
» Replies: 3
» Views: 1466
1971 Mach 1 parting out interior parts -...
Last Post: ylwhrse
12-22-2022 01:38 PM
» Replies: 0
» Views: 640
Painting
Last Post: Rare Pony
12-14-2022 06:24 PM
» Replies: 2
» Views: 1964
WELCOME ALL NEW MEMBERS INTRODUCE YOURSE...
Last Post: JTS71 Mach1
08-31-2022 01:36 PM
» Replies: 82
» Views: 157028
1970 mach 1 matching numbers
Last Post: Kstweeter
08-31-2022 10:31 AM
» Replies: 1
» Views: 1086
Brake booster/servo hose length
Last Post: JTS71 Mach1
08-23-2022 09:40 AM
» Replies: 7
» Views: 2995
New Member
Last Post: JTS71 Mach1
08-20-2022 11:18 AM
» Replies: 2
» Views: 1498
smooth window operation on 70 Mach
Last Post: CUSTOMMISER
08-15-2022 12:10 PM
» Replies: 2
» Views: 1473
Blinkers on solid
Last Post: busted21
08-09-2022 03:58 AM
» Replies: 14
» Views: 8717
Blinkers on solid when lights on.
Last Post: JTS71 Mach1
08-08-2022 12:06 PM
» Replies: 1
» Views: 1719
351 cj running hot
Last Post: busted21
08-08-2022 12:13 AM
» Replies: 5
» Views: 3403
Major Winter projects
Last Post: JTS71 Mach1
07-09-2022 05:12 AM
» Replies: 49
» Views: 21264
Happy Fathers Day!!!
Last Post: JTS71 Mach1
06-20-2022 02:34 AM
» Replies: 0
» Views: 1685
1969 Raven Black 390 Looking For
Last Post: mason1958
06-11-2022 09:48 AM
» Replies: 10
» Views: 15079

>