Emission testing, emission failures and repairs.
#1
The yearly emission test of your car is nothing more than a test to see how much fuel you are sending out the tailpipe that is not being used by your engine. Think of an emission failure as a huge gas leak, because that is exactly what it is.

To pass emissions, you must tune your engine to properly consume the gasoline that's being delivered to it and convert it to energy to move the car down the road.

The emissions test is an easy way to determine if the right mixture of air and fuel is being delivered. It also can check to see if the ignition system is working ok. As a matter of fact, when trying to fix a driveability problem, most good technicians will take a look at the vehicles tail pipe readings first. These readings will give them direction.

When you fail because of high limits of HC or hydrocarbons, it means there is raw fuel that is being sent out the tailpipe because your engine isn't converting the fuel to energy. The raw fuel actually washes the protective layer of oil off moving parts inside your engine and contributes to engine wear which can lead to premature failure. Some common causes are spark plugs, spark plug wires, misadjusted timing or vacuum leaks.

When you fail because your CO or carbon monoxide is too high, that means the fuel and air ratio is way off and there is evidence of incomplete combustion or burning of the air/fuel mixture. Most of the common causes relate to the carburetor or the fuel delivery system. A CO failure will always be rooted in the carburetor or fuel injection system. CO failures are not fixed with spark plugs.

If there is too much fuel and not enough air, a CO failure is usually seen. When there is too much air and not enough fuel, a HC failure is generally seen.

In 1976, the first year of vehicle emissions testing in Arizona, no one was forced to fix their car if it failed. The following year, 1977, it was mandatory that failed vehicles were fixed before renewal tags were issued.

The volume of tested vehicles over the last 10 years has steadily risen from 12 million vehicles to 18 million. The failure rate 10 years ago was 22% of the tested cars. In 1991 we were at 15%. We are clearly making positive progress towards cleaning up our air.

The failure rate by model year shows that the first year tested, 1967 vehicles, have a 35% failure rate. The failure rate declines to 28% for the 1974 year vehicles. 1975 Shows a failure rate of 31% and from there it shows a steady decline to 1996, where less than 1% of all vehicles fail. So much for old car enthusiasts (which includes me) saying their cars are not part of the air quality problem!

Let's group some vehicle years together and look at the failure rate in the state of Arizona:

1967-1980 have an initial failure rate of 33.6%.

1981-1996 Have an astounding low failure rate of 12.73%.

If we look at just 88-96, they have a initial failure rate of 3.8%

Talk about the progress of technology!

I don't know the name of the provider of centralized testing in Arizona, but their test equipment passed over 97% of the time it was tested for accuracy. Other emissions analyzers at fleet testing and certified repair facilities passed 86% of the time. This should eliminate your technician from saying that his equipment is right and "their's" is off.

So given the choice, I'm sure most of you would rather benefit from all the fuel you buy as opposed to having a large portion of it be wasted and end up polluting our air.

By the way, the best way to insure your car will pass its emission test is to make sure you hold the idle up to about 2,000 rpm while waiting in line of for at least 3 minutes prior to the test.

Here is an article we wrote about emissions failures for the
more advanced do-it-your-selfers:

As technology increases and more emphasis is being placed on air quality, many states and municipalities have instituted vehicle inspection/maintenance (I/M) programs, most of which include tail-pipe exhaust emissions testing. The center of the controversy is the internal combustion engine, which converts the chemical energy stored in fuel into heat. The heat is released by simple combustion. Perfect combustion changes hydrocarbons (HC) into carbon dioxide (CO2) and water (H2O).

Unfortunately, perfect combustion happens only under laboratory conditions. At any other time, the result is less than perfect combustion and undesirable emissions. The three major pollutants are carbon monoxide (CO), hydrocarbons (HC), and oxides of nitrogen (NOX).

Carbon monoxide (CO), is incompletely burned fuel or to be more precise are hydrocarbon molecules that split apart but don't burn in the combustion cycle. High (CO) is the result of one problem, a rich air/fuel mixture but may have several causes. Hydrocarbons (HC) is simply unburned fuel that escaped the combustion cycle.

Oxides of nitrogen (NOX) are a little more complicated. At engine combustion temperatures above (2500 F), nitrogen (which makes up 80% of our atmosphere) bonds with oxygen to form oxides of nitrogen (NOX). Normally these two gases are like oil and water, they don't mix. The exhaust gas recirculation valve (EGR) is designed to introduce metered amounts of exhaust gases back into the intake manifold, displacing a portion of the incoming air/fuel mixture to the cylinders. This process reduces high combustion temperatures and controls NOX.

Here's some common causes for the production of these three pollutants.

CO Failures (vehicles with carbs)

1. Engine not at operating temperature. Example, engine/cat cooled off while waiting in test line or has a stuck open or missing t-stat.

2. Bad or maladjusted float level.

3. Plugged air bleed passages or misadjusted main metering system, leaking fuel passages or gaskets.

4. Maladjusted idle air/fuel mixture screws.

5. Ruptured or sticking canister purge valve.

6. PCV plugged or drawing in fuel contaminated oil vapors.

7. Malfunctioning mixture control device.

8. Malfunctioning computer inputs. Example: O2 sensor defective, reading lean all the time. MAP sensor vacuum hose being clogged or broken (reading a heavy load all the time). Coolant temperature sensor having high resistance or open circuit (reading "cold engine" all the time). Throttle position sensor stuck or open ground, (reading wide open throttle).

9. Contaminated, restricted or bad catalytic converter.

CO Failures (fuel injected vehicles)

1. Any of the computer components listed above.

2. Leaking or bad injectors.

3. Mass air flow sensors (voltage or frequency being too high).

4. Fuel pressure too high (restricted fuel return line or stuck fuel regulator)

5. Ruptured fuel regulator (fuel leaking directly into intake)

HC Failures (all vehicles)

1. Engine was not at normal operating temperature.

2. Ignition system malfunction. Spark failing to occur for any reason will send unburned hydrocarbons (HC) down the exhaust pipe. Example: bad plugs, plug wires, distributor cap, rotor, coil wire, coils, etc.

3. An extremely lean fuel mixture that causes misfiring. Examples include disconnected, leaking or misrouted vacuum hoses, intake gasket leaks, EGR stuck open, low fuel pressure.

4. Over advanced timing. Insufficient spark duration.

5. Low compression or mechanical problems. Worn rings, burned valves, bad or misaligned timing gears.

6. Over rich fuel condition causing both HC and CO failures.

7. Contaminated, bad, or restricted catalytic converter.

NOX failures (all vehicles)

1. Improper operation of the EGR valve. Stuck open, obstructed, leaking, or misrouted EGR vacuum lines.

2. Plugged EGR passages. Carbon build up in passages.

3. Over advanced timing.

4. Too lean of fuel mixture.

5. Engines cooling system in poor condition, causing excessive temperature.

6. Malfunction of the electronic spark control (ESC), and knock sensor. Computer fails to retard timing.

7. Contaminated or bad catalytic converter.

What about Carbon Dioxide (CO2)?

CO2 is not a pollutant. CO2 is a byproduct of good combustion. CO2 is highest when the engine and catalytic converter are operating at maximum efficiency. The reason I bring this up is because the CAT can be a hidden cause for emissions failures in all categories. Testing of the cat would be the last step after looking at everything else. CO2 can only be measured with a four gas analyzer. Here is a fool proof method of testing CATs to see if they are capable of doing their job:

1. Warm the vehicle up to full operating temperature.

2. Shut the engine off and disable fuel and ignition systems.

3. Crank engine over at wide open throttle for 10 seconds, to purge fuel vapors from exhaust.

4. Insert analyzer probe into tailpipe.

5. Connect a propane enrichment device to a large manifold vacuum source, brake booster or PCV hose.

6. Turn propane half way on and crank engine injecting propane into the cylinders and then into the cat.

7. Note HC and CO2 readings after 10 seconds.

HC should be off the scale and CO2 should read 8 to 13%. If the CO2 reads less than spec, like under 5%, then the CAT is unable to convert HC to CO2. If the CAT is defective, replace it with a unit approved by EPA.
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Starter system testing procedure Masol 4 13,027 09-26-2015, 12:58 AM
Last Post: Mach1FatherFigure

Forum Jump:


Users browsing this thread: 1 Guest(s)
[-]
Latest Threads
What's One More Iron In The Fire!
Last Post: fram lee666
03-18-2024 06:21 PM
» Replies: 125
» Views: 238053
"Jacobra"
Last Post: JTS71 Mach1
06-30-2023 11:13 PM
» Replies: 86
» Views: 150853
My old Queensland Ambulance
Last Post: JTS71 Mach1
06-30-2023 11:08 PM
» Replies: 5
» Views: 1685
New member from San Jose, CA
Last Post: JTS71 Mach1
05-09-2023 08:39 AM
» Replies: 12
» Views: 3957
Saving Seatbelts
Last Post: Jim
02-19-2023 10:23 PM
» Replies: 2
» Views: 9109
Sourcing new wheels
Last Post: JTS71 Mach1
01-25-2023 02:34 PM
» Replies: 1
» Views: 1995
Shaker Air Filter
Last Post: JTS71 Mach1
01-08-2023 02:24 AM
» Replies: 3
» Views: 1466
1971 Mach 1 parting out interior parts -...
Last Post: ylwhrse
12-22-2022 01:38 PM
» Replies: 0
» Views: 640
Painting
Last Post: Rare Pony
12-14-2022 06:24 PM
» Replies: 2
» Views: 1964
WELCOME ALL NEW MEMBERS INTRODUCE YOURSE...
Last Post: JTS71 Mach1
08-31-2022 01:36 PM
» Replies: 82
» Views: 157026
1970 mach 1 matching numbers
Last Post: Kstweeter
08-31-2022 10:31 AM
» Replies: 1
» Views: 1086
Brake booster/servo hose length
Last Post: JTS71 Mach1
08-23-2022 09:40 AM
» Replies: 7
» Views: 2994
New Member
Last Post: JTS71 Mach1
08-20-2022 11:18 AM
» Replies: 2
» Views: 1498
smooth window operation on 70 Mach
Last Post: CUSTOMMISER
08-15-2022 12:10 PM
» Replies: 2
» Views: 1472
Blinkers on solid
Last Post: busted21
08-09-2022 03:58 AM
» Replies: 14
» Views: 8715
Blinkers on solid when lights on.
Last Post: JTS71 Mach1
08-08-2022 12:06 PM
» Replies: 1
» Views: 1719
351 cj running hot
Last Post: busted21
08-08-2022 12:13 AM
» Replies: 5
» Views: 3403
Major Winter projects
Last Post: JTS71 Mach1
07-09-2022 05:12 AM
» Replies: 49
» Views: 21263
Happy Fathers Day!!!
Last Post: JTS71 Mach1
06-20-2022 02:34 AM
» Replies: 0
» Views: 1684
1969 Raven Black 390 Looking For
Last Post: mason1958
06-11-2022 09:48 AM
» Replies: 10
» Views: 15079

>