Replacing rear leaf springs on a 1969 Mach 1
#1
I took the opportunity this summer to drive my ’69 Mach 1 to the 30th Mid-American Ford/Shelby Performance Meet in Tulsa, Oklahoma. The drive was 175 miles one way and was the longest distance I’d driven the car. The Mach did perform flawlessly with one exception, body lean at speed. I was fortunate that most of the trip was on the interstate but the car rolled excessively in the rear on the off ramps and cloverleafs. I promised myself I would not take the car on another trip like this until I replaced the rear springs.

       

After researching my options and discussing it with my local Mustang parts dealer I decided on the five-leaf performance spring. Here are the steps I took to replace them. This should be the same process for any ’64 – ‘73 Mustangs. It was a simple straightforward project for me and took less than half a day.

Parts and Tools

New leaf springs (you can have your old ones re-arched) 4 U-Bolts and nuts (optional) 2 sets of rear bushings or Shackle kits (optional) 2 front mounting bolts (optional) 4 Jack stands or blocks 11/16” socket/wrench for U-Bolts ½” wrench for shocks 9/16” wrench for shackles 2 ea. ¾” socket wrenches for front mounting bolt (may need breaker bar, torch, saw or divine intervention as noted below) Water pump pliers (may need, see procedure) Penetrating oil

       

Lift car with jack on the frame rail behind the leaf’s front mount. Remove wheel and place a block or jack stand under the end of the frame rail. My blocks look a little precarious but each board was nailed to the one below it and they were very steady. If you have any doubts use jack stands. Your life is at risk.

   

Place a block or jack stand under the differential. You need to match the height of the frame block/stand. Then do #1 and #2 for the other side of the car.

   

Start with either side and take the bottom mounting hardware off of the shock and push it up out of the way. Remove the U-bolts and the lower shock mounting plate, which hold the differential to the spring.

               

Remove the mounting nuts from the rear shackle and remove the shackle. This is a tight area and has to be done with a hand wrench. This job would have been much easier with a ratcheting hand wrench. The rear of the spring will drop to the ground when you remove the shackle. I used some penetrating oil on the rubber bushings and twisted them with water pump pliers to get them out of the frame rail.

Remove the front mounting bolt. I put penetrating oil on a day or two ahead of time and mine was easy to remove. You must put a second socket wrench on the bolt inside the frame. NOTE THAT THIS BOLT CAN BE DIFFICULT TO REMOVE. On some cars this bolt rusts solid to the frame and may have to be cut using a torch, “Sawzall”(reciprocating saw), or right angle grinder. Once you get this bolt out the spring will be free.

Reverse this procedure to install your new springs starting with installing the front mounting bolt. The new springs will include a new front bushing. You may reuse your U-Bolts if they are in good shape but they are not very expensive to replace. You may also want to replace the bushings in the shackles or buy new shackle kits. Once again, not very expensive and you’re probably not going to want to do this again for a while.

The arch of the old and new springs look very similar but the handling is very different. The height of the car was not changed. The rear of the car hugs the road now and my body roll issue is resolved.

       

My Mach has another improvement and it only took a few hours. The new springs will cost $150 - $200 with new shackles, bushings and hardware. The cost varies depending on whether you go with stock or performance versions. A lot of suppliers offer kits. Mine were around $200 but I have seen stock springs alone for under $100.

   
By: Mike Campbell
Reply
#2
Nice write up? How do you like the 5-leaf pack so far? I went with the 5-leaf performance pack that are supposed to be 1 inch lower. They actually set the same as the old springs once they were installed. It's a little stiff, but no body roll and the car really hooks up pretty well. I also added a 1 inch lowering block afterwards to get the stance I wanted.
Reply
#3
Nice writeup. I am preparing to replace the springs on my 70 so the inof provided is great.
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Leaf spring shackles bmehling54 3 3,642 12-28-2020, 01:29 AM
Last Post: JTS71 Mach1
  "70 Mach 1 with TCI torque Tube Rear Suspension 70MACH427 0 4,845 12-28-2018, 05:31 AM
Last Post: 70MACH427
  Rear Leaf Springs demon69 5 10,332 06-29-2018, 10:46 PM
Last Post: demon69
  wheels and tires for 1969 dk fuelish 1 6,158 04-06-2018, 02:09 PM
Last Post: 1969_Mach1
  1969 mach 1 - best tires to buy for steel wheel rims rindel 5 16,668 05-08-2015, 10:57 PM
Last Post: mrmach1
  Borgeson 800330 DOES fit 1969 Mach 1 351w with air Must69ang 7 24,289 09-13-2014, 10:50 AM
Last Post: Must69ang
  1969 351W Power steering pressure hose - 2 part hose? Must69ang 9 22,284 05-16-2014, 01:01 PM
Last Post: Must69ang
  Source needed for 1969 Power steering pump with reservoir Must69ang 4 14,894 05-16-2014, 01:26 AM
Last Post: Must69ang
  What wheels for a 70 Mach 1 ???? Masterblaster7212 12 37,821 03-20-2014, 03:01 AM
Last Post: Masterblaster7212
Photo 1969 front end rebuild. Mcanical 3 12,015 05-27-2012, 03:25 PM
Last Post: Mcanical

Forum Jump:


Users browsing this thread: 1 Guest(s)
[-]
Latest Threads
What's One More Iron In The Fire!
Last Post: fram lee666
03-18-2024 06:21 PM
» Replies: 125
» Views: 238147
"Jacobra"
Last Post: JTS71 Mach1
06-30-2023 11:13 PM
» Replies: 86
» Views: 150929
My old Queensland Ambulance
Last Post: JTS71 Mach1
06-30-2023 11:08 PM
» Replies: 5
» Views: 1707
New member from San Jose, CA
Last Post: JTS71 Mach1
05-09-2023 08:39 AM
» Replies: 12
» Views: 3966
Saving Seatbelts
Last Post: Jim
02-19-2023 10:23 PM
» Replies: 2
» Views: 9115
Sourcing new wheels
Last Post: JTS71 Mach1
01-25-2023 02:34 PM
» Replies: 1
» Views: 2003
Shaker Air Filter
Last Post: JTS71 Mach1
01-08-2023 02:24 AM
» Replies: 3
» Views: 1468
1971 Mach 1 parting out interior parts -...
Last Post: ylwhrse
12-22-2022 01:38 PM
» Replies: 0
» Views: 641
Painting
Last Post: Rare Pony
12-14-2022 06:24 PM
» Replies: 2
» Views: 1971
WELCOME ALL NEW MEMBERS INTRODUCE YOURSE...
Last Post: JTS71 Mach1
08-31-2022 01:36 PM
» Replies: 82
» Views: 157080
1970 mach 1 matching numbers
Last Post: Kstweeter
08-31-2022 10:31 AM
» Replies: 1
» Views: 1087
Brake booster/servo hose length
Last Post: JTS71 Mach1
08-23-2022 09:40 AM
» Replies: 7
» Views: 3007
New Member
Last Post: JTS71 Mach1
08-20-2022 11:18 AM
» Replies: 2
» Views: 1501
smooth window operation on 70 Mach
Last Post: CUSTOMMISER
08-15-2022 12:10 PM
» Replies: 2
» Views: 1482
Blinkers on solid
Last Post: busted21
08-09-2022 03:58 AM
» Replies: 14
» Views: 8729
Blinkers on solid when lights on.
Last Post: JTS71 Mach1
08-08-2022 12:06 PM
» Replies: 1
» Views: 1720
351 cj running hot
Last Post: busted21
08-08-2022 12:13 AM
» Replies: 5
» Views: 3411
Major Winter projects
Last Post: JTS71 Mach1
07-09-2022 05:12 AM
» Replies: 49
» Views: 21302
Happy Fathers Day!!!
Last Post: JTS71 Mach1
06-20-2022 02:34 AM
» Replies: 0
» Views: 1686
1969 Raven Black 390 Looking For
Last Post: mason1958
06-11-2022 09:48 AM
» Replies: 10
» Views: 15089

>